Status Report - Springs removed

[jlaird]

Am about 3/4 inch from haveing first bolt drilled out. Two drills so far so went to Home Depot and got four more of the good ones. Built a little wooden thing so I can apply pressure upwards on the drill. Seems to be working fine so far. Maybe tomorrow will finish, I hope. Took quite a while to develope a procedure so lot of wasted time today.

 

[jlaird]

Re: Status Report - Spring

Man does this job eat 10 buck drills.

 

[SilentUnicorn]

Re: Status Report - Spring

you should be able to get thru the job on a drill,, maybe two. How fast are you running the drill and what size is it? i would suggest a slower speed, certianly not full rabbit on the drill. spin slow, push hard.


mark

 

[jlaird]

Re: Status Report - Spring

Ho, got it out, I am the worlds expert on removeing springs now.

Hears how:

Drill the two front bolts up past the first leaf.
Drill the middle bolt up past the first leaf.

Pry the lower leaf loose and remove.

All the remander will come out at that point.

Isn't it easy when you know how.

Thanks guys for all the support and good ideas.

 

[GB1]

Re: Status Report - Spring

<font color="blue"> </font>GREAT!!! /ubbthreads/images/graemlins/cheers.gif

 

[john_j]

Re: Status Report - Spring

[ QUOTE ]
Man does this job eat 10 buck drills.

[/ QUOTE ]

Have you tried sharpening them?

 

[jlaird]

Re: Status Report - Spring

Well kind of, will clean em up now that I have a break.

 

[Trevor Jessie]

Re: Status Report - Spring

If you do not have a Drill Dr. ... ask for one for your Bday, fathers day, whatever gift giving event arises.

 

[jlaird]

Re: Status Report - Spring

Hmmm, Drill Dr. Have a sharpner for small bits but not this 3/8 and I have found I can not do much of a job free hand.

 

[jcatnite]

Re: Status Report - Spring

I've never had much luck with Drill Doctors. I mostly use left handed drill bits for bolt and screw removal anyway. I get the best results with a vise and my trusty dremel.
JC

 

[Trevor Jessie]

Re: Status Report - Spring

The Drill Dr. comes in handy when you when you are needing to make clean holes with very little wandering of the bit (once it is in the material). A good edge at the proper pitch make a big difference. But, it would not be to useful for left handed bits. Just my opinion. There are many other tools that are more useful, but the Drill Dr. makes me more apt to use a sharp bit than try to get by with an "OK" bit just to save time.

 

[tony barnhill]

Re: Status Report - Spring

I'm getting a Drill Dr. for my birthday - I just know it!

 

[jlaird]

Re: Status Report - Spring

Think I will take all my bits to tonys so he can get some good practace.

 

[DrEntropy]

Re: Status Report - Spring

Good plan Jack!!! We'll "circle th' wagons" at your house. I've a TON of bits wot need some 'attention.' /ubbthreads/images/graemlins/yesnod.gif

 

[msoylemez]

Re: Status Report - Spring

Hey jlaird,

how about some pics?? All of this talk--gotta see the progress...

 

[jlaird]

Re: Status Report - Spring

Well shucks, ok.

 

[RobSelina]

Re: Status Report - Spring

started removing the bolts on my rear springs today too...got three out on the drivers side with some patience and penetrating oil. Passenger side I've got one and broke one so far (ugh!).

Left the remainder soaking tonight and I'll try again tomorrow. Then I get to drill and tap the broken one (hopefully still only one)....