• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)

TR2/3/3A post 6k tr3 trunk brace

Share this page

S

sp53

Yoda
Offline
Hi all here is my latest challenge with my post 6k tr3. I was putting the trunk lid on and had a lot of difficulty with the inner brace that removes. Perhaps the body shop should have done the bodywork with the brace on the truck because after I wrestled the brace on the trunk sits up in the back. I bought the car as a basket case and figured the brace would just pop right on and act as a support, but that was not the case. I had to push and pull with a helper and felt lucky to get the thing on without damaging the something. Any comments on others experiences is greatly appreciated.
Steve
 
Steve,

Sorry, I don't have any experience with body work on the TR3 yet. It does sound like something is warped (either trunk lid or brace if that's possible).

Hopefully someone else here has some experience and advice.

Scott
 
Scott,
I just picked up a late trunk lidand bonnet yesterdy for my post 6k body,as my project came with early ,flat hinge trunk and hood.
This trunk lid has tubular supports,with the hinge side held in by the hinge bolts.Mine doesnt have the hinge in place,and the holes line up with no coaxing.
Hood panel is cherry.
Hope this helps
Tom
 
Steve, here are some pics of the interior of my boot lid. My car is a post 60000 3A. The only thing that we took off prior to going toit the body shop was the boot lid stay rod bracket at the hinge area.
Hope this is of some help.

Tinkerman
 

Attachments

  • 22251.jpg
    22251.jpg
    85.2 KB · Views: 343
  • 22252.jpg
    22252.jpg
    91 KB · Views: 338
  • 22253.jpg
    22253.jpg
    84.6 KB · Views: 339
Thanks Dick for the picks they help me see that I bolted it up right despite the way mine pushes the lid up in the back. On yours are they bolts in the back or some other type of hardware, like pin or?
Steve
 
They are bolts. I just didn't take it apart when it all went to the body shop. I have some other issues but but not on the boot lid.
If you need more pictures let me know.

Dick
 
Tinkerman,It appears you are missing the rubber cushions that go between the support rods and panel.Mine has four ,about 3 inches long,in the center of each brace tube.
was wondering if these are available if I remove to paint.
Funny my early lid looks much better built with steel channel braces,independent of hinge mount.
Tom
 
I thought that they were only on the Bonnet. I have them for it. I can order some more, I think TRF has them on sale. Have to check...........

Thanks Tom, Tinkerman
 
You were right Tom, they are needed for both the boot and bonnet lids. TRF does have them on sale.

Thanks Dick
 
Hadn't looked at mine in quite awhile Tom, so I just did and your right. No cross tubes. Thanks for the heads up!
Dick
 
Hi Dick and Tom you have both been helpful, Dick for the pics and Tom for information about the rubber piece. However, I cannot find it in the TRF catalog. My mind cannot work with too much of that clicking around to find stuff. I guess that is why I use Moss so much. Having said that I often do like the stuff I get from TRF better. Incidentally, after looking at your pics Dick, I figured out what I did wrong with the brace. I bolted it on the inside of the rear supports and not the outside. I mean it took me and the pope to get that thing in there and know I have to try and get it out. I need higher help again.
Steve
 
Steve
I have a set of the rubber crosstube braces if you need them. Brand new from TRF.........I didn't need them. PM me and I'll be happy to send them to you.
Gordon
 
Again, thanks Gordon and let me know what the shipping is. In addition, we have some pretty good tr3 people out on the West coast with some parts, so if you need something give a ring.
Steve
 
Thank you for the little rubber brace brackets Gordon they arrived yesterday, and they will have a good home.
Steve
 
Back
Top