• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)

Dowel bolt location

Share this page

GregW

GregW

Yoda
Offline
I have a question that I should know the answer to but, well, I don’t. Where do the dowel bolts that are used to align the bell housing to the rear engine plate go? I know that one goes through #1 in the picture below, but the Moss site and my manual don’t show where the second bolt goes. Thanks, Greg
178279-rearplate.jpg
 
You guys and your fancy graphics, I'm a bit jelious.

Note to self: speek with son on how that is done.
 
The Otter one goes through # 6 hole Greg---Keoke- /ubbthreads/images/graemlins/grin.gif
 
Hi Randy,
You must know that I’ve installed my tranny, which makes you pure evil. /ubbthreads/images/graemlins/devilgrin.gif /ubbthreads/images/graemlins/jester.gif
 
Hey Keoke have you taken to keeping Otters then /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif
 
[ QUOTE ]
Hey Keoke have you taken to keeping Otters then /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif /ubbthreads/images/graemlins/lol.gif

[/ QUOTE ]

Well Andrew, I had to you see the dowel bolt locations, when referenced to hands on a clock, come out as 11-and-5 oclock, Consequently, I couldn't figure out how to get the hands of Big Ben in the cubby box but the Otters fit in a nick.---Keoke /ubbthreads/images/graemlins/wink.gif
 
[ QUOTE ]

The Otter one goes through # 6 hole Greg---Keoke- /ubbthreads/images/graemlins/grin.gif

[/ QUOTE ]That's a transmission bolt(hole), no?
 
Yep Randy both go through the bell Housing.---Keoke
 
[ QUOTE ]

Yep Randy both go through the bell Housing.---Keoke

[/ QUOTE ]
Okay, but not that low; there's no engine block on the forward side of that (#6) hole, just a gap before the sheetmetal oil pan.

mgc3.sized.jpg


Please note: that's an MGC XMSN, not an original Healey's.
 
Randy;
Only the one at 11 oclock threads into the engine block.---Keoke
 
Hi Randy,
The 2 dowel bolts are used to center the transmission to the engine. They should be the first to be fitted but they were back-ordered when I installed the tranny and I just haven’t gotten around to putting them in now that I have them. I think you’re talking about the dowels that locate the back plate to the engine block. Without those installed, the dowel bolts wouldn’t be very helpful. I think I've confused myself now. /ubbthreads/images/graemlins/crazyeyes.gif
 
[ QUOTE ]
Hi Randy,
The 2 dowel bolts are used to center the transmission to the engine. They should be the first to be fitted but they were back-ordered when I installed the tranny and I just haven’t gotten around to putting them in now that I have them. I think you’re talking about the dowels that locate the back plate to the engine block. Without those installed, the dowel bolts wouldn’t be very helpful. I think I've confused myself now. /ubbthreads/images/graemlins/crazyeyes.gif

[/ QUOTE ]
Yep, that's what I thought you were asking about. My bad.
 
Whew!!---Keoke-- /ubbthreads/images/graemlins/laugh.gif

Greg, check the "bolts" for tightness in the bellhousing holes they should be a slight friction fit.
 
Hi Keoke,
Thanks for the heads up on the bolt fit. I got sidetracked and couldn’t work on the car much last weekend.
 
Back
Top