• Hi Guest!
    If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
    There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Subscribers don't see this gawd-aweful banner
Tips
Tips

Seat Belts Installed This Weekend

Share this page

Thanks Duane. Might you have a picture of the QR bracket currently installed in the car?
And how did you fit the carpet over the transmission tunnel bracket?

Patrick
 
PHulst said:
Thanks Duane. Might you have a picture of the QR bracket currently installed in the car?
And how did you fit the carpet over the transmission tunnel bracket?

Patrick
Click to expand...

Patrick,

Unfortunately I have not installed my QR bracket yet, so no picture. I'm really hoping Olin will post pictures of his original ones since I've never seen an install of the original BMC Kit!!

I'm planning on utilizing the information from the instruction manual contained on pages 5 and 6 (Below) as my guide, removing the interior pieces and cutting the holes in the interior trim as recommended in the manual.

https://rhynard.org/images/AH/seat_belt_asj.pdf
 
Csarneson said:
I believe that reinforcement plate is designed to be installed from the backside. The instructions suggest cutting a 1.5" hole in the tunnel as the first step. It would probably be a little stronger that way.
Click to expand...

Csarneson,

I installed it as the original diagram (Below) detailed, but installed the bolts in the opposite direction since it's much easier to get a small wrench to hold in the tight space than a Phillips. I'm guessing they opted for the front face installation so the reinforcing plate and the seat belt bolt would not be adjacent to the propeller shaft!! I agree it would be stronger the other way, but you would also have difficulty connecting the belt with the insulation and carpet. I'm hoping Olin will post pictures of his installation.

Thanks,
Duane



Capture.jpg
 
Duane_Rhynard said:
Csarneson,

I installed it as the original diagram (Below) detailed, but installed the bolts in the opposite direction since it's much easier to get a small wrench to hold in the tight space than a Phillips. I'm guessing they opted for the front face installation so the reinforcing plate and the seat belt bolt would not be adjacent to the propeller shaft!! I agree it would be stronger the other way, but you would also have difficulty connecting the belt with the insulation and carpet. I'm hoping Olin will post pictures of his installation.

Thanks,
Duane
Click to expand...

Duane,

Take a look at the written installation instructions you posted. They say to install the reinforcing plate from inside the tunnel. Bet the installation wold be a PITA that way, though but it would give quite a bit more strength in case of an accident as right now you're depending on six small bolts in shear to hold your body from the windshield.
 
Here's an example of how I think they are supposed to be installed. It's not my photo. Just found it on the web. Looks like they plug welded it from the backside instead of using screws for a cleaner install. I don't think you have to worry about space for the driveshaft. You have lots of space side-to-side in there.

seamsealer3.jpg
 
Csarneson said:
Here's an example of how I think they are supposed to be installed. It's not my photo. Just found it on the web. Looks like they plug welded it from the backside instead of using screws for a cleaner install. I don't think you have to worry about space for the driveshaft. You have lots of space side-to-side in there.

View attachment 40916
Click to expand...

My BJ7 came with the mount installed by the factory and looks as the one in your picture. The mount Duane shows is from the BMC kit made for cars before the mounting became standard. There's some more on the BMC kits here: https://mgaguru.com/mgtech/accessories/at116.htm
 
Csarneson said:
Here's an example of how I think they are supposed to be installed. It's not my photo. Just found it on the web. Looks like they plug welded it from the backside instead of using screws for a cleaner install. I don't think you have to worry about space for the driveshaft. You have lots of space side-to-side in there.

View attachment 40916
Click to expand...


You (and Rick) are correct, the instructions very clearly state that the plate is installed this way.

Thanks Guys!
Duane
 
Duane_Rhynard said:
You (and Rick) are correct, the instructions very clearly state that the plate is installed this way.

Thanks Guys!
Duane
Click to expand...

The only fly in the ointment is the installation requires the presence of, gulp, the dreaded "Assistant" to secure the phillips screws while you attach the nuts inside the driveshaft tunnel.
 
Duane,

I was happy to check back tonight and see all the discussion. I will post pictures tomorrow, I had a problem with the right eye and I am trying to take it easy for a while. I have a picture of the kit before I installed them that I will post also.
 
steveg said:
The only fly in the ointment is the installation requires the presence of, gulp, the dreaded "Assistant" to secure the phillips screws while you attach the nuts inside the driveshaft tunnel.
Click to expand...

Even worse, the directions require installing the phillips screws from inside the tunnel with the nuts and washers on the inside of the interior!
 
Csarneson said:
Here's an example of how I think they are supposed to be installed. It's not my photo. Just found it on the web. Looks like they plug welded it from the backside instead of using screws for a cleaner install. I don't think you have to worry about space for the driveshaft. You have lots of space side-to-side in there.

View attachment 40916
Click to expand...

My 10/61 tri-carb also came with this setup. If you notice the holes for the mounting bracket on the floor, you can see it is slightly raised about a 1/16" due to the added reinforcement.
 
Here are the close-up pictures of my setup.

Floor Bracket:

IMG_5965.jpg


Buckle Receiver:



IMG_5966.jpg

Side view of Buckle Opening:

IMG_5967.jpg

Adjuster and Buckle (note that the adjuster has a plastic coating):

IMG_5968.jpg


Tunnel attachment (Special spacer is used here):

IMG_5969.jpg


Shoulder Strap Attachment (There is a slight bend in this piece so there is room for the belt to connect to the bracket):

IMG_5970.jpg
 
Olin,

Thanks for all the pictures they are great! I appreciate you taking the time to post them.

HealeyRick said:
Even worse, the directions require installing the phillips screws from inside the tunnel with the nuts and washers on the inside of the interior!
Click to expand...


Rick,

Not too bad on the two-seaters through the battery hatch! I did not even need the dreaded assistant. :tennis:

Thanks for everyone's help!

Duane


a6.jpg
a4.jpg





Pictures of original '61 Tri-carb Mounting Points (My next project once I finish my BN6):

a3.jpg
Passenger Compartment Tunnel with Rubber Insert

a7.jpg
Inside Tunnel From Under Car

a2.jpg
Interior

a1.jpg
Rear Wheel Well

a5.jpg
Passenger Floor
 
Last edited:
Duane,

Great set of pics, especially the original mounting points in the tri-carb. If you have a photo of the inside of the tunnel mount, that would be helpful. The pictures in the thread above show the mounting of the "kit" with the six screws & nuts, where-as the original mount was welded from behind. In this set-up was the plate not extended to the chassis rail to give a bit more robustness in the design.

Andy
 
BBH said:
Duane,

Great set of pics, especially the original mounting points in the tri-carb. If you have a photo of the inside of the tunnel mount, that would be helpful. The pictures in the thread above show the mounting of the "kit" with the six screws & nuts, where-as the original mount was welded from behind. In this set-up was the plate not extended to the chassis rail to give a bit more robustness in the design.

Andy
Click to expand...
Andy,

It does not extend to the chassis rail on my car. I would think that the force it would take to rip it out of the tunnel as it is, would be so great that you would probably not be able to survive without a broken shoulder and back.
 
steveg said:
Duane - In picture a6 above, is the inner nut welded to the circular piece?
Click to expand...
The inner nut is not welded to the reinforcement plate. That is unfortunate, because you will have to go underneath the car to remove the bolt anytime you want to remove the carpeting in that area.
 
Back
Top