• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
Tips
Tips

Wobbly Distributor Cap??

Share this page

T

tiddlers

Freshman Member
Country flag
Offline
Anyone had issues with cap-fit? If so, how did you correct it?
I have a BJ8 with 25D dizzy. The Lucas cap doesn't seem to fit snugly leaving the inside unevenly worn. I checked- there is very little play in the bushing/shaft, but upon further inspection, I noticed the cap had a little wobble- while clipped in place you could rock it just a bit. Inside the cap, two of the contacts were gouged where the rotor had nibbled them back a bit, while the rest of the contacts had the familiar gray powdery crust. She's running fine, I replaced the cap just this past summer and only put 50 miles on her in the fall. My concern is that A) there should be no gouges B) I need to replace this cap because gouges are not good and C) it seems like the cap should fit better. Any suggestions or thoughts are appreciated.
 
Replace the cap and be sure the hold down springs are good
 
If you have the proper cap there cannot be any movement. The cap fits like a jig saw puzzle piece. The bottom of the cap is irregular to match the top of the dizzy, not smooth. Movement would throw everything off. The BJ8 should have side mounted HT wire mountings.
TH
 
Check with XK's Unlimited
They just made an incorrect buy[for Jags] and have side entry 6 clyn Healey caps for sale.??
 
$_35.JPG


  • $_33.JPG
  • $_33.JPG


NOS Dist Cap Austin Healey 3000 BJ8 Aston Martin DB6 DBS Landrover Series 6 Cyl.


  • $29.95
  • + $13.34 Shipping


Condition:--
Popularity:1 watching
Sold by:User ID tanaman (Feedback score 3772)
100% Positive feedback
Delivery:Estimated Apr. 4- Apr. 12
From:Canada
Returns:Not accepted
Covered by eBay Money Back Guarantee - opens in a new window or tab
Watch Item


So!! What chu waiti on-----:highly_amused:

 
Last edited:
XKs might be better as you could return it if it's cr*p.

I wonder if the Canadian one is good or if it's poorly made.

Lately the ones from Moss have had quality issues - the screws don't pierce the sheath in the proper place. Rather they can be off to one side or too far back to hold.
 
I wonder if the Canadian one is good or if it's poorly made.Yeah I saw that "no returns" :


But it is made in England Steve, Look on box.
 
Have heard from a reliable source that some are buying NOS boxes (only) at flea markets and putting aftermarket parts in them. Just sayin'.

I bought what appears to be a NOS Lucas cap from Gary Hemphill many--probably 20 or more--years ago and it was $40 then. When the original caps were manufactured I don't believe aluminium was in widespread usage, so if the cap has Al terminals--instead of brass--it's likely not NOS. My theory only, if I'm full of sludge just say so.
 
:friendly_wink:--What does NOS stand for?

There are at least 59 definitions of NOS.

For example:
Naked on stage---:highly_amused:

Do not confuse it with OEM parts.
 
A couple of hen's teeth:

That one from Canada appears to be one of the good, old aftermarket caps at a very reasonable price. That seller also has an earlier-style cap with the copper terminals in what looks like as-new condition.

Question: do the 25D BJ8-style original Lucas caps have the word "Lucas" embossed on them?
 
steveg said:
A couple of hen's teeth:

That one from Canada appears to be one of the good, old aftermarket caps at a very reasonable price. That seller also has an earlier-style cap with the copper terminals in what looks like as-new condition.

Question: do the 25D BJ8-style original Lucas caps have the word "Lucas" embossed on them?
Click to expand...
I believe I have an original nos cap (spare),for my bj8 and it has Lucas embossed on it.
 
Patrick says:
"I believe I have an original nos cap (spare),for my bj8 and it has Lucas embossed on it. "

Yep you are correct.
 
tahoe healey said:
If you have the proper cap there cannot be any movement. The cap fits like a jig saw puzzle piece. The bottom of the cap is irregular to match the top of the dizzy, not smooth. Movement would throw everything off. The BJ8 should have side mounted HT wire mountings.
TH
Click to expand...

When you say "not smooth", I'm assuming you're writing about the minor elevation differences in the main mating on the dizzy versus the obvious notches. If so, which of the suggested caps is contoured with those variances? I pulled the distributor, and it is definitely the fact that my cap face is smooth along its mating face, and the distributor mating face is not.
 
Tahoe Healey wrote:
[h=2]Re: Wobbly Distributor Cap??[/h]
If you have the proper cap there cannot be any movement. The cap fits like a jig saw puzzle piece. The bottom of the cap is irregular to match the top of the dizzy, not smooth. Movement would throw everything off. The BJ8 should have side mounted HT wire mountings.
TH

I replied, but apparently incorrectly. So, again-
When you say "not smooth", I'm assuming you're writing about the minor machined elevation differences in the main mating surface on the dizzy versus the obvious notches. If so, which of the suggested caps is contoured with those variances? I pulled the distributor, and it is definitely the fact that my cap face is smooth along its mating face, and the distributor mating face is not.​
 
If I understand you correctly, you are saying that the surface at the top of your distributor that the cap fits against is not smooth. Aside from the notches that fit the notches on the cap, the surface should be smooth. If you could post a picture, that would help.
 
blueskies said:
If I understand you correctly, you are saying that the surface at the top of your distributor that the cap fits against is not smooth. Aside from the notches that fit the notches on the cap, the surface should be smooth. If you could post a picture, that would help.
Click to expand...

Look at about 4 & 8 o'clock. It isn't a uniform surface, it's machined that way. I'm guessing the uneven wear I witnessed in the cap was a little bad luck... perhaps the cap was a tad off center or the clips were not properly seated.
 

Attachments

  • IMG_2928.jpg
    IMG_2928.jpg
    40.7 KB · Views: 146
tiddlers said:
Look at about 4 & 8 o'clock. It isn't a uniform surface, it's machined that way. I'm guessing the uneven wear I witnessed in the cap was a little bad luck... perhaps the cap was a tad off center or the clips were not properly seated.
Click to expand...
I would at first glance say that the dizzy needs to be filed/shaved so the cap surface is perfectly flat.
 
Back
Top