Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
When I rebuild my Midget, I plan on installing a roll bar, but I would like to know if there are any available tonneau covers to fit over the roll bar, or am I up a creek, and will have to make one from scratch. I'd like to know if it would be worth my while, or should I just leave that (attaching)hardware off the car to save a few bucks.
-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Tonneu cover over roll bar.
- Thread starter adam70
- Start date
Share this page
77_MG_Midget
Jedi Trainee
Offline
Personally, I like the looks of a rollbar in my LBC. I haven't heard of a tonneau cover that will fit over the rollbar though. I haven't checked yet, but I'm sure an upholstery shop could take an original tonneau and modify it to fit around the roll bar.
Biff
Jedi Trainee
Offline
Adam70,
It is possible to modify a standard tonneau cover for a roll bar. I did it to my tonneau using velcro and some small pieces of vinyl to make little flaps which covered the slits I made for the rollbar. I have a short tonneau on my Bugeye and cut slits from the first lift-a-dot to and around the rollbar upright. On each side of the slit I sewed on the little flaps. To the flaps I sewed on the velcro. where i had to cut the circle to go around the rollbar upright I cut the circle in a star pattern, folded the star cuts under and then sewed the edge for a finished look. No one makes a tonneau cover for a rollbar as each installation/rollbar would be different. Either modify an original tonneau or have one custom made.
It is possible to modify a standard tonneau cover for a roll bar. I did it to my tonneau using velcro and some small pieces of vinyl to make little flaps which covered the slits I made for the rollbar. I have a short tonneau on my Bugeye and cut slits from the first lift-a-dot to and around the rollbar upright. On each side of the slit I sewed on the little flaps. To the flaps I sewed on the velcro. where i had to cut the circle to go around the rollbar upright I cut the circle in a star pattern, folded the star cuts under and then sewed the edge for a finished look. No one makes a tonneau cover for a rollbar as each installation/rollbar would be different. Either modify an original tonneau or have one custom made.
aeronca65t
Great Pumpkin
Offline
When #11 was a street car, I did something similar to Biff. You will not be able to find a cover that is already set up for the roll bar, but an auto upolstry shop (or a place that does boat covers) could probably do the job reasonably. Don't let it discourage you from putting in a roll bar....that's a good idea!
thanks for the tip, gents. I also saw the thing over on the MGB section, about those loose covers that go over the windshield and those look like a viable option as well. I guess I'll cross that bridge when I get there. It just doesn't hurt to get a good solid ground plan going
thanks again.
thanks again.
GreenHornet
Jedi Trainee
Offline
I have a roll bar on my 59 Sprite. I too just cut a slice just behind the rear of the doors and cut two cirles out to accomodate the roll bar tubes. Nuthin fancy but it does the job!