• Hi Guest!
    If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
    There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Subscribers don't see this gawd-aweful banner
Tips
Tips

Sounds like a good deal for someone

Share this page

That is a good deal! That is what I paid for a similar product 15 years ago (but without the holes!). If someone is interested in purchasing it, I could be of help as it is located within a reasonable distance from me!
 
You could turn your Bugeyed Sprite into a Shark Sprite! /bcforum/images/%%GRAEMLIN_URL%%/thumbsup.gif
 
John Moore said:
That's been up on ebay for some time now.
Click to expand...

I have also seen it re-listed a couple of times!! If it is a racing hood, it may be a bit flimsy for street use, but definitly a weight-saver!!
 
Hi
I think i may be interested. Not racing but my bonnet been bent and fixed and then tweaked. It is not a good fit.
I am only interested in street use. Think I could get this to fit with little gaps at the side. I have about 1.5 inch gap on left side.
I think if it was warped in thick plastic and insured for twice the value it would arrive here in Calif with out a problem. Please let me know.
Thanks
sim
 
Sim, please check your bonnet hinges. The high one sounds like it is bent. It can be straightened with a large screw driver in the hole in the bottom of the hinge and bending forward.

You have to remove the hinge from the bonnett and brace it up out of the way just a bit. Pad things well and give it a try. Worked for me.

If bonnet is low in the center put a padded 2x4 on the battery and lower the bonnet to bend it up a bit. Bending it down is more difficult but you get the idea.
 
that was interesting as I walked by the car about 1 hour ago, I thought "that hinge is the problem". I will give that a try.Bet it got bent in the wreck the car was in when I bought it. That is story I must tell sometime.
I think I may still be interested in the fiberglass one
 
Had my bonnet off so was easier, could measure hinges in various positions my drivers side one was 1/4" high. Now matches and expect to fit bonnet end of this week for sure.

Was a front corner accident as well some long time ago.
 
on mine the surface that the hinge plate sits on is dented in about 3.8 of inch on left side. The right side is just fine.
I will try the fix when I pull the engine for Transmissions repair
 
Great, you will have to get it right reguardless of which bonnet you use. Instead of trying to bend the bonnet mount where it is dented think about washers.
 
i was very close to making a deal on that hood the first time he posted it, seller ended up balking....perhaps he would be open to an offer this time around?

I kinda liked the vents cut in the hood. Im thinking about doing the same thing to my steel hood.
 
I have had a 'glas hood for years, and would recomend it! (KEEP! you old metal one however - I didn't /bcforum/images/%%GRAEMLIN_URL%%/mad.gif !!!!), but be prepared to make it flip forward, it is easier to install and has many benefits! You might as well if you are making the switch (you can retain the old mounting holes, etc. for going back to the original!). /bcforum/images/%%GRAEMLIN_URL%%/thumbsup.gif
PS: see other theads for front-flip setup! /bcforum/images/%%GRAEMLIN_URL%%/wink.gif
 
yup the plan is to go front flip. I am thinking about recessing some driving lights where the original turn signals would go. Theres a street rod shop here that has headlight housings that have the turn signal indicators in the same housing as the headlight.

Anyone tried the minimania front tilt hinge kit?

I still need to come up with a better radiator to help keep the rotary engine cool.
 
My dad has a set of those headlights in his streetrod. They are very nice units.
 
Back
Top