• Hi Guest!
    You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
    There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Subscribers don't see this gawd-aweful banner
Tips
Tips

removing front crossmember...

Share this page

kennypinkerton

kennypinkerton

Yoda
Offline
OK, I think I'm going to attempt it this weekend (if it stops raining for a while).

After I disconnect the front brake hoses, and remove the 4 bolts, is there anything else holding or hanging onto the front crossmember? What holds the cardboard sheild on - screws or rivets?
 
Steering rack - Front sway bar.

Look up underneath the cardboard mud guard & you'll see a little bolt with a nut on it in the center.....in addition to the screws along the edge back up on top.

Be careful that the bolts holding the crossmember come out easily - the one closest to the exhaust is probably rusted solid & you may have yo undo it from underneath.
 
Thanks Tony. I forgot about the swaybar. Isn't the steering rack mounted to the crossmember?

Gonna spray the bolts down with PB tomorrow evening when I get home from work.

I guess I need to tighten the nuts on the motor mount whil I've got it all out. I need to find my new driver's side motor mount around the house here too. It's been here for 5 years, forgot where I put it :crazy:

I figure that new bushing kit I got from you will go on easier while sitting on the front porch instead of me laying on my back with the fireants :laugh:
 
Steering rack is mounted to crossmember but you have to loosen it from the column & with it attached to the crossmeber, you'll have to drop the member down & forward.
 
kennypinkerton said:
Isn't the steering rack mounted to the crossmember?
Click to expand...

Yes it is. Might I also suggest you disassemble the suspension while the cross member is still on the car? It makes removal of the beam almost a one-handed job, versus a 100-pound awkward lump. It also gives you more leverage to tweak on things, and makes coil spring removal far easier for those without a spring compressor.
 
tony barnhill said:
Steering rack is mounted to crossmember but you have to loosen it from the column & with it attached to the crossmeber, you'll have to drop the member down & forward.
Click to expand...
I typically unbolt the rack from the cross member, tie it up out of the way, and leave it there while I pull the cross member. Of course you have to pop the tie rods off of the steering arms but that's easier than disconnecting the steering column and it has to be done anyway.
 
I agree its easier to disassemble while on the car if you're gonna rebuild & put back under the car...however, I've never had any problems disassembling on the floor....& have never had a spring do anything except pop the spring pan down a little & fall out onto the floor (that's usually how I disassemble parts car front suspensions - some time after I drop the beam when I need a particular part off the beam.)
 
be careful. That's just what I did. I pulled out the front suspension to rebuild it.. then look what happened...

front3_4.jpg
 
Tim -

I'm curious, did you remove the unibody to make it easier to work on the suspension from the top? :jester: I'm about to pull my front suspension out, but if you think it's easier your way, I'll try it and let you know how it goes!
 
Looks like he had a heck of a time finding the right bolts
 
Now that's a SERIOUS case of getting attacked by the Might-As-Wells.....heck, you got attacked by a whole planet of them!!! :laugh: ROFL
 
I have neither the money, nor the time. I'll just stick to the stuff I can afford. Although in a few years, the Alfa may look like that.

"your unibody fell off"

:lol:

Was probably trying to find out how to get to the bonnet hinges... "Hmmm, maybe if I take that off I can get to them..."
 
sorta like my little Midget that went down to tub just to change the clutch!
 
Back
Top