-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Rear axle oil seal
- Thread starter TonyR
- Start date
Share this page
Bob_Spidell
Yoda
Offline
It's not particularly difficult; and has been discussed frequently on this forum, including here:
https://www.britishcarforum.com/bcforum/ubbthreads.php/topics/763253/Rear_Hub_Puller#Post763253
The securing nut is 8-sided, and a typical 6- or 12-point socket will not work. Several parts houses, and British Tools (britishtools.com)--sell a stamped steel socket, and Randy Forbes (on this forum) has fabricated the definitive tool. You will need a proper socket (I'd bet someone has removed/installed yours before with channellocks or a chisel and hammer).
You pull the axles out, remove the nut, and then pull the entire axle hub. You can reverse the axle and use it as a platform against the axle housing and tighten nuts on the studs. That will get the hub about halfway out, then use a large, three-legged gear puller. Randy uses a slide hammer with another fabricated adapter to bolt up to 3 of the 5 studs.
You have to remove the bearings--check for wear, or maybe even replace on principle while you're at it--to get to the seal. I use a hydraulic press to remove them; a vise can be used. R&R on the seal is typical (smear a little grease on the inside lip to minimize startup wear).
Getting the hub back on can be a chore, too. I like to warm them up a little in an oven--200degF maybe--then I 'persuade' them back on with a suitably sized steel tube used as a drift and a 3-lb persuader (hammer).
You'll need to replace the seals, maybe the bearings, the paper gasket and the tab-type lockwasher if it's been used up.
This is an all-day job for both sides, assuming you have all tools and parts ready to go. Make sure the axle housing is properly supported--you'll be applying some effort to it and if it slipped off jackstands (or blocks, etc.) it would be disastrous.
https://www.britishcarforum.com/bcforum/ubbthreads.php/topics/763253/Rear_Hub_Puller#Post763253
The securing nut is 8-sided, and a typical 6- or 12-point socket will not work. Several parts houses, and British Tools (britishtools.com)--sell a stamped steel socket, and Randy Forbes (on this forum) has fabricated the definitive tool. You will need a proper socket (I'd bet someone has removed/installed yours before with channellocks or a chisel and hammer).
You pull the axles out, remove the nut, and then pull the entire axle hub. You can reverse the axle and use it as a platform against the axle housing and tighten nuts on the studs. That will get the hub about halfway out, then use a large, three-legged gear puller. Randy uses a slide hammer with another fabricated adapter to bolt up to 3 of the 5 studs.
You have to remove the bearings--check for wear, or maybe even replace on principle while you're at it--to get to the seal. I use a hydraulic press to remove them; a vise can be used. R&R on the seal is typical (smear a little grease on the inside lip to minimize startup wear).
Getting the hub back on can be a chore, too. I like to warm them up a little in an oven--200degF maybe--then I 'persuade' them back on with a suitably sized steel tube used as a drift and a 3-lb persuader (hammer).
You'll need to replace the seals, maybe the bearings, the paper gasket and the tab-type lockwasher if it's been used up.
This is an all-day job for both sides, assuming you have all tools and parts ready to go. Make sure the axle housing is properly supported--you'll be applying some effort to it and if it slipped off jackstands (or blocks, etc.) it would be disastrous.
Offline
Offline
While you're in there examine carefully the machined surface of the stub axle. If it is deeply grooved put a speedi-sleeve on it and the new seal will actually work!