Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
OP
racingenglishcars
Darth Vader
Offline
Come down and see the test engine sometime.
-
Hey Guest!
British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!**Upgrade Now**
(PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
I need some pictures
- Thread starter racingenglishcars
- Start date
Share this page
OP
racingenglishcars
Darth Vader
Offline
I saw your homepage now. That is exactly what I need to see. Thanks a lot, and now I will continue to disassemble and straighten.
BTW, I am getting all the tub parts in 3 to 5 days except the boot floor and bonnet air-box. They come later. So I can start this weekend with aligning and welding next week.
Donn
BTW, I am getting all the tub parts in 3 to 5 days except the boot floor and bonnet air-box. They come later. So I can start this weekend with aligning and welding next week.
Donn
GB1
Yoda
Offline
i updated my site with 4 shots under the body section. i also have some rough measurements and can get some more if you want specific ones:
length from front firewall to top of rear panel - 35"
height shifter hole front lip to bottom tunnel floor - 11 1/8"
height shifter hole rear lip to bottom tunnel floor - 8 7/8"
width from tunnel to passenger sill - 20 3/8" (measured at rear of shift hole)
.
hopefully some of this helps ....
FMichaels posted this on another thread and I think his intention was to place it here.
well at least I hope /bcforum/images/%%GRAEMLIN_URL%%/wink.gif
Patrick
length from front firewall to top of rear panel - 35"
height shifter hole front lip to bottom tunnel floor - 11 1/8"
height shifter hole rear lip to bottom tunnel floor - 8 7/8"
width from tunnel to passenger sill - 20 3/8" (measured at rear of shift hole)
.
hopefully some of this helps ....
FMichaels posted this on another thread and I think his intention was to place it here.
well at least I hope /bcforum/images/%%GRAEMLIN_URL%%/wink.gif
Patrick
OP
racingenglishcars
Darth Vader
Offline
Well, Thanks guys. I seem to have done it. You all were a great help and I couldn't have done it without you.
It's a lot easier moving some of the structure when some other surrounding it is missing.
My measurements were correct with yours, except rear shifter hole height was 1/8 too low, but that got fixed. Also my firewall to rear edge was 34 1/2. I don't know if there were some assembly tolerances or if the rear bulkhead had been pushed forward a bit, or both. Since I'm putting on a new bulkhead, I can try to pull it back a bit.
It's a lot easier moving some of the structure when some other surrounding it is missing.
My measurements were correct with yours, except rear shifter hole height was 1/8 too low, but that got fixed. Also my firewall to rear edge was 34 1/2. I don't know if there were some assembly tolerances or if the rear bulkhead had been pushed forward a bit, or both. Since I'm putting on a new bulkhead, I can try to pull it back a bit.