-
Hi Guest!
You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Compression woes
- Thread starter MY66AH
- Start date
Share this page
dklawson
Yoda
Offline
The HF leak down tester doesn't have a great reputation. For about the same money you can make your own following plans on the net. If you are fortunate enough to have some surplus air fittings around the garage it costs next to nothing to make your own. Of course your time is valuable also.
Regardless, the leak down test will tell you more than the compression test alone and the direct connection of air to the cylinders as Kurt suggested can often tell you all you need to know. Just don't forget to take off the radiator cap when hooking air up either directly with a hose or with the leak down tester.
Regardless, the leak down test will tell you more than the compression test alone and the direct connection of air to the cylinders as Kurt suggested can often tell you all you need to know. Just don't forget to take off the radiator cap when hooking air up either directly with a hose or with the leak down tester.
65_BRG_Sprite
Jedi Warrior
Offline
Man I love that color- especially as it ages. (Don't know how to spell "patiniates")
I've always liked primrose as well...only the aging thing is what I DID'NT like. Seemed to fade big time.
Kurt.
I have the HF leakdown tester. It works fine. The only trick is establishing the baseline pressure is like steering a big ship. If you're low and you increase the flow too quickly, you overshoot your mark, and vice versa. You can also let it run "wide open", which can allow you to listen/observe the air leak if it is in the valves.
Head gasket is a likely culprit, however, I know in my case and other folks on BCF that the head gasket failure tends to be between cylinders 2 and 3, not 3 and 4 (or is it 1 and 2? I always forget which way to start counting).
Head gasket is a likely culprit, however, I know in my case and other folks on BCF that the head gasket failure tends to be between cylinders 2 and 3, not 3 and 4 (or is it 1 and 2? I always forget which way to start counting).
dklawson
Yoda
Offline
Start at the water pump and count back. Between 2-3 seems to be the most common HG failure location.
I chose to build my own leak down tester. I opted for the 2 gauge configuration. With it, all you do is supply a bit more than 100 PSI to the tester's regulator, dial the regulator output to 100 PSI, and read the downstream gauge after the inline .040" orifice. There are no other adjustments.
I chose to build my own leak down tester. I opted for the 2 gauge configuration. With it, all you do is supply a bit more than 100 PSI to the tester's regulator, dial the regulator output to 100 PSI, and read the downstream gauge after the inline .040" orifice. There are no other adjustments.
I started to build one by knocking the porcelain out of an old plug and brazing in a air fitting. When I hooked up the air and used a length of hose to listen through the burned valves on my MGA became very obvious so that was as far as I got. If I was trying to determine wear I would have to finish the project.
Kurt.