Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Offline
Has anyone bought and installed the Auto Parts Warehouse brake booster for an Austin Healey 3000, part number N4000-43709? The price of $420 is attractive if it works.
Charlie
Charlie
-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Brake Booster
- Thread starter Coastalman
- Start date
Share this page
davelgee
Senior Member
Offline
You might want to have a look at this... https://www.performancebritish.com/proddetail.php?prod=LockheedBB
Cheers!
Dave G.
Cheers!
Dave G.
OP
Offline
The price gets even better! Did you use this one?
Charlie
Charlie
GregW
Yoda
Online
Hey Charlie,
I installed a PBR booster that I haven’t had any problems with in the limited amount of driving I’ve done with my car. Other people who have used this part seem satisfied also. Not quite as cheap at $349, but it comes with mounting brackets. It has a bleeder valve to help get air out of the system.
I installed a PBR booster that I haven’t had any problems with in the limited amount of driving I’ve done with my car. Other people who have used this part seem satisfied also. Not quite as cheap at $349, but it comes with mounting brackets. It has a bleeder valve to help get air out of the system.
OP
Offline
Greg,
Did the PBR just bolt in, or did you need a bracket kit?
Charlie
Did the PBR just bolt in, or did you need a bracket kit?
Charlie
BlueRidge1
Jedi Warrior
Offline
I think I read somewhere that the master cyl. is slightly differnt between a non booster car and one with the booster. May want to verify this before the upgrade if you currently have no booster. Bob
OP
Offline
I do have a booster, but the brakes are hard to push. Car does stop, but much pressure must be applied to the pedal. The brake pedal is slightly further down than the clutch or accelerator pedals. I am going to check into aligning the pedals per instructions on one of the posts.
Charlie
Charlie
Keoke
Great Pumpkin
Offline
[ QUOTE ]
I do have a booster, but the brakes are hard to push. Car does stop, but much pressure must be applied to the pedal. The brake pedal is slightly further down than the clutch or accelerator pedals. I am going to check into aligning the pedals per instructions on one of the posts.
Charlie
[/ QUOTE ]
Given that you have a booster Charlie, then it just may be that the booster was added without changing the master cylinder over to the correct size as mentioned by BR1.--Keoke-?
I do have a booster, but the brakes are hard to push. Car does stop, but much pressure must be applied to the pedal. The brake pedal is slightly further down than the clutch or accelerator pedals. I am going to check into aligning the pedals per instructions on one of the posts.
Charlie
[/ QUOTE ]
Given that you have a booster Charlie, then it just may be that the booster was added without changing the master cylinder over to the correct size as mentioned by BR1.--Keoke-?
OP
Offline
Keoke,
My car is a '66 BJ8. Shouldn't it have the correct master cylinder for a booster?
Charlie
My car is a '66 BJ8. Shouldn't it have the correct master cylinder for a booster?
Charlie
OP
Offline
Guys, thanks for the information. I will order a PBR booster.
Charlie
Charlie