• Hi Guest!
    You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
    There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Subscribers don't see this gawd-aweful banner
Tips
Tips

Crank Pulley Removal

Share this page

M

mylesw

Jedi Hopeful
Offline
Hello

I'm having a hard time getting the crank pulley off my engine...and yes, the nut has been removed. I'm using a puller and have got to the point where the yoke of the puller is bending rather that the pulley moving. Any suggestions about how to give the pulley more encouragement to move...?

Thanks

Myles
 
mylesw said:
Hello

I'm having a hard time getting the crank pulley off my engine...and yes, the nut has been removed. I'm using a puller and have got to the point where the yoke of the puller is bending rather that the pulley moving. Any suggestions about how to give the pulley more encouragement to move...?

Thanks

Myles
Click to expand...

Myles I had your same problem, and I had to give it to the Machine Shop that was going to grind the cylinders and valves on the head for them to take out, I don't know how they took it out but, if you want, I can ask tomorrow, I have to go as they have some more items they are sandblasting for me now.

Ignacio
 
Myles,
The key may have worn a new path into the pulley. Try rotating it in the opposite direction of normal running, with the crankshaft locked up. You can use the bolts holding the damper on as an attachment point. You didn't say if the engine is in the car or not. Good luck.
Bob
 
Engine is still in the car...luckily I have a Welch race chassis which has a removable yoke so I have good access to the pulley.

Myles
 
We always wacked the screw head with a hammer to help things along. That being said, I don't know what type of puller you have nor how it sits on the end of the crank. You gotta be sure that whatever you have won't damage the end of the crank both tightening it up or wacking it. Last thing you want to do is beat up the end of your crank.
 
me61ic said:
Myles I had your same problem, and I had to give it to the Machine Shop that was going to grind the cylinders and valves on the head for them to take out, I don't know how they took it out but, if you want, I can ask tomorrow, I have to go as they have some more items they are sandblasting for me now.

Ignacio
Click to expand...

I already asked, they said they did not remember having any problem removing. They said if your puller is bending you should maybe get a tougher one, and hit the pulley close to the crankshaft (making sure you don't hit the crankshaft) with a flat chisel to break it free if it does not move...:encouragement:

Good luck
 
Heat heat heat is your friend . break out the gas axe .
 
The gas axe could be a bit excessive, try a hot air gun. If you have a Welch racing chassis - is it the standard pulley you have or the new Australian harmonic balancer - these can only be put on when warmed up and heat will help remove it if your puller is not up to it.

:cheers:

Bob
 
Bob Hughes said:
The gas axe could be a bit excessive, try a hot air gun. If you have a Welch racing chassis - is it the standard pulley you have or the new Australian harmonic balancer - these can only be put on when warmed up and heat will help remove it if your puller is not up to it.

:cheers:

Bob
Click to expand...

Not really . A heat gun is too slow all you will end up doing is heating the pulley , the crank and everything around it slowly . you need concentrated high heat quickly to get the pulley to expand faster than the crank and it will pop right off .
 
Heat the outside dia.of pulley then work the heat closer to the center of puller, if you have some heat gloves it will probably pull off with your hands, trick is to do this quick, as not to get crankshaft hot. It may take several tries. Best of luck, Bob
 
Hi Myles, If the center pin on your puller is bending, I would think it's time to use another puller. The way to use the puller is to put tension on the center pin, then strike the center pin hex head with a hammer. Strike the pin toward the crank shaft. This should shock it loose. I hope this helps.
Bobby R
 
Back
Top