Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Received my SS hydraulic lines from Classic Tube yesterday. Any suggestions/hints/things to avoid when fitting & bending the tubes. Especially the shipping bends!! I did purchase a tube bending tool to help in the process. The SS tubes do appear to be pretty "stoudt"!!
-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Tube Bending
- Thread starter ralph_s
- Start date
Share this page
Offline
I had to do a bunch of rebending to get things to line up with my stainless lines from Classic Tube. I did a mixture of using my bending tool and my fingers to to the bending.
Basic advice is to go slow, and just tweak a little bit at a time. The SS lines are harder to bend, so some force will be necessary but be careful!
I was able to get all my lines in place without too much trouble, just needed some persuasion in place. Lots of breaks when I got frustrated helped as well.
Basic advice is to go slow, and just tweak a little bit at a time. The SS lines are harder to bend, so some force will be necessary but be careful!
I was able to get all my lines in place without too much trouble, just needed some persuasion in place. Lots of breaks when I got frustrated helped as well.
JodyFKerr
Jedi Knight
Offline
Take a gander at this:
https://www.theymightberacing.com/ShopTech/FuelBrakeLineFabrication.aspx
My biggest tips:
1) fill (and compact the fill) with sand. Will keep you from accidentally crimping the line.
2) Go slowly!
3) Use an angle measure to measure your bends (against the original stock if available).
Cheers!
Jody
https://www.theymightberacing.com/ShopTech/FuelBrakeLineFabrication.aspx
My biggest tips:
1) fill (and compact the fill) with sand. Will keep you from accidentally crimping the line.
2) Go slowly!
3) Use an angle measure to measure your bends (against the original stock if available).
Cheers!
Jody
texas_bugeye
Jedi Knight
Offline
I do a lot a ss.1/4 tube bending for control valves.
Get a good quality bender,nothing worse than a bad tool it can make or break the job. Apply some silicone spray to the pipe and the bender , take your time ,think it thru, take your time.Oh did I mention take your time? well If I didn't Jack did.
Get a good quality bender,nothing worse than a bad tool it can make or break the job. Apply some silicone spray to the pipe and the bender , take your time ,think it thru, take your time.Oh did I mention take your time? well If I didn't Jack did.
I did some tube bending as described in the sample web album, may not be perfect, but functional and no kinks.
And all that talk about going slowly.......thats the key.
My lines were copper and copper-nickel, so they were easier to work with than stainless steel.
Photo : Several of the brake and fuel line results:
https://picasaweb.google.com/minorsands/mgmidget1973#5360712504275246498
Cheers,
And all that talk about going slowly.......thats the key.
My lines were copper and copper-nickel, so they were easier to work with than stainless steel.
Photo : Several of the brake and fuel line results:
https://picasaweb.google.com/minorsands/mgmidget1973#5360712504275246498
Cheers,
