• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
Tips
Tips

TR6 TR6 Hazard lights

Share this page

R6MGS

R6MGS

Yoda
Offline
I think this was brought up before, but I just want to confirm....The only thing not wokring on my TR6 is the hazard lights, I suspected the relay but was told the later TR6's didn't have a seperate relay for the hazard lights? I assume the relay is built into the flasher unit? and that there is a seperate flasher unit for the hazards? If so where is it located?

Thanks
Ron
 
Not sure where the relay is, but wanted to comment; the little bulb in my 6's pull-out switch never worked because it would not stay in the socket. I used a small piece of plastic wrap over the hole when the bulb was fitted, then screwed it tight and peeled off the excess, thus forcing the bulb to stay put--works like a charm.

Good luck with the relay question.
 
[ QUOTE ]
that there is a seperate flasher unit for the hazards? If so where is it located?

[/ QUOTE ]

On my 71' TR6 there is a flasher unit located under the passenger side dash /ubbthreads/images/graemlins/england.gif
 
Ron,

From what I recall, on my '76 the flasher relay is in the passenger footwell, and the hazard relay is in the engine compartment next the fuse box. I'd go outside and check, but it's just gone to the shop for a spot of welding....

Mark
 
Thanks for the replies? So the relay and flasher are seperate? Do the hazards and turn signals share a flasher?

BTW: Does that buld have to be in the socket properly in order to make the hazards work? Cuz mine doesn't sit in there right either, think I'll try the saran thing.
 
No, mine worked before I fixed the bulb. But Mark T is correct; the hazard relay is on the driver side, under the hood, near the fuse box. I remembered after his post.
 
Thanks, thats what I had thought too.
Now wheres the flasher? and is it seperate from the turn signal flasher(cuz those work fine)
 
As was said. in an early car it is in the passenger seat well
 
On my '72 the turn signal flasher is located in the passenger footwell. Actually up on the outboard side of the footwell. The hazard flasher is in the engine bay next to the fuse box.

/ubbthreads/images/graemlins/cheers.gif
 
Ron,

The '72 - '76 model TR6s do not have a hazard flasher relay, only the '69 - '71 models do. The switching function that was provided by the relays in the earlier models is provided by a special switch in the later models.

There are separate flashers for the TS and the hazard functions. As stated above, the TS flasher is located above the passenger footwell, and the hazard flasher is located near the fuse box under the hood.

Go to https://www.advanceautowire.com and click on the "stock schematics" button on the left. This will lead you to a set of colorized wiring diagrams for the TR6 which you can download and print. Looking over the diagram for your '76 should make all this clear.

Occasionally, the TS and hazard flasher units are referred to as "relays," which they are not. This can sometimes lead to confusion when working with these components. A relay functions quite differently than the flashers.
 
Thanks, thats what I was lead to believe before. Now that you've confirmed it I can get to work......I suspect the flasher by the fuse box....Is there any way to test a flasher it see if it's good or not?
 
The fuse box item is not a flasher but a relay.
 
[ QUOTE ]
The fuse box item is not a flasher but a relay.

[/ QUOTE ]

Well, yes and no. If the car has a hazard relay, it will be found to the rear of the fuse box. Relay or not, the flasher will be found to the front of the fuse box.
 
[ QUOTE ]
Is there any way to test a flasher it see if it's good or not?

[/ QUOTE ]


For a '72 or later model, probably the best way to test it is to replace it and see if it works. Go to your local auto parts store and buy a type 552 flasher, for about 2 bucks or so. Pull the old flasher and reconnect the wiring to the new one. The terminal designations on the Lucas flasher are "B" and "L". On the one you buy at the parts store will have terminal designations "X" and "L". The "X" correspondes to the "B" and the "Ls" are the same.

If you have a '69-'71 model, you will need to buy a Tridon model 550 in the short can (any other make or the tridon in a tall can won't work properly). In this case, the Lucas terminals are "B", "L", and "P". On the aftermarket, they are "X", "P", and "L". "X" = "B", "L" and "P" = "L" and "P".

The only other way to really test one is to hook up a load and see if it works. I keep a pair of bulbs handy that I've soldered together with short pieces of wire for testing purposes. The flasher won't work unless it has a reasonable load on it, so a simple voltmeter won't help.
 
Thanks for all the help guys, looks like I've got something else to do this weekend. I'll let ya know when I get it fixed.
 
Nah, this stuff never scares me.....I'll get it fixed ASAP...got the next 2 weeks off of work(starting tonight) so I'll have some time to mess with it then. I just know it's gunna be on of those fiddly little jobs that will kill an entire afternoon in what seams like an hour.
 
Got `em going....bypassed the flasher, lights went on...so then I knew it was definatly the flasher...Went to Peninsula Imports to get a new flasher...Brought it home....It was defective! By now I was getting pretty frustrated, so I just went to the local parts store and bought the closest one I could find...Works like a charm /ubbthreads/images/graemlins/laugh.gif

Thanks to everyone for your advice
 
Back
Top