-
Hi Guest!
You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
TR2/3/3A TR3B Oil Drain Plug
- Thread starter af3683
- Start date
Share this page
TR3driver
Great Pumpkin - R.I.P
Offline
TR3B should have a plug with tapered threads, meaning no gasket is required or possible. But it's possible someone has fitted a pan from an earlier TR, which did use a gasket.
Assuming you do have the tapered plug version, I suggest cleaning and inspecting the threads. Damage is usually pretty obvious. You can use a suitable tap to clean up the threads in the pan; obviously replace the plug if it's buggered.
I'm not a fan of the factory plug, they seem very soft and prone to round off; plus lack a magnet. I use a hex socket plug (meaning you need an Allen wrench to turn it) with a magnet from MMC
https://www.mcmaster.com
Some teflon (aka PTFE) pipe "dope" will help the threads seal, and also make it easier to get out next time. Any place that sells plumbing should have it (Home Depot, Menards, Ace Hardware, OSH, whatever they have in your area). Eg, https://www.homedepot.com/p/RectorSeal-T-Plus-2-in-4-oz-Teflon-Pipe-Thread-Sealant-23631/100201204
Or if you want something more extreme, there is a Loctite product for sealing pipe threads:
https://www.amazon.com/Loctite-Strength-Thread-Sealant-White/dp/B000O03DLE
Assuming you do have the tapered plug version, I suggest cleaning and inspecting the threads. Damage is usually pretty obvious. You can use a suitable tap to clean up the threads in the pan; obviously replace the plug if it's buggered.
I'm not a fan of the factory plug, they seem very soft and prone to round off; plus lack a magnet. I use a hex socket plug (meaning you need an Allen wrench to turn it) with a magnet from MMC
https://www.mcmaster.com
Some teflon (aka PTFE) pipe "dope" will help the threads seal, and also make it easier to get out next time. Any place that sells plumbing should have it (Home Depot, Menards, Ace Hardware, OSH, whatever they have in your area). Eg, https://www.homedepot.com/p/RectorSeal-T-Plus-2-in-4-oz-Teflon-Pipe-Thread-Sealant-23631/100201204
Or if you want something more extreme, there is a Loctite product for sealing pipe threads:
https://www.amazon.com/Loctite-Strength-Thread-Sealant-White/dp/B000O03DLE
Geo Hahn
Yoda
Offline
I got a magnetic plug from one of the major vendors (possibly Moss) but the magnet used was rather weak. I pried it out and substituted a rare earth magnet which does collect stuff (mostly a glob of thick oil that [probably contains some very fine metal).
I have since just added a rare earth magnet to conventional plugs - JBWeld works well for that.
One other benefit to the magnetic plug is that after you remove it and wipe it clean you can just stick it on the side of the oil pan - saves you looking for it later.
I have since just added a rare earth magnet to conventional plugs - JBWeld works well for that.
One other benefit to the magnetic plug is that after you remove it and wipe it clean you can just stick it on the side of the oil pan - saves you looking for it later.
I tried the various thread sealers with no luck. What finally worked for me was permatex fuel reistant gasket sealer, comparable to blue hylomar. Drain oil. Thoroughly clean all threads (i used carb cleaner) both on plug and hole. Apply a very little hylomar to both plug, and hole. Screw in a few threads to spread it, then unscrew and let flash off (sit ten or 15 minutes until acetone odor is gone . Thread in plug, let sit 24 hrs. Then add oil.
TR3driver
Great Pumpkin - R.I.P
Offline
NPT and BSPT are different pitches in this size. A mismatch would not just be prone to leaks!
Since I've been using NPT plugs for decades, and no significant leaks, I'm fairly certain those threads are NPT. I do smear a little fresh pipe dope on them each time, but it's more to make them easy to remove next time than for leaks.
I will add that it's very easy to get fooled. A small leak higher up (like the pan gasket or fuel pump gasket) can be undetectable as it runs down; but form a very obvious drop on the lowest point.
One way to tell is to get some of that foot powder that goes on liquid and quickly dries to a white powder. Clean the area, then paint with the foot powder. It will change color if oil touches it.
Offline
I have no where near Randall's experience and don't remember ever replacing a drain plug, so just assumed they were BSP, but the point was that the the TPI and pitch on both are close enough in most sizes (3/8?) that either will screw into the hole, but of course cause a leak if mismatched.
That plug is one of the few places on my engine that I don't ever remember leaking. No sealant, dope, tape or goo either, so probably a good idea to look above it.
Tom
That plug is one of the few places on my engine that I don't ever remember leaking. No sealant, dope, tape or goo either, so probably a good idea to look above it.
Tom
Offline
I'm quite sure the TRF plugs are correct and same with Moss and the others and as Randall and others have been using NPT plugs, then that's what they are. My suggestion seems to have puts us off on a tangent. My point was new correct plug from a reliable source (TRF) would be a cheap fix or at least help with the diagnosis.
Tom
Tom