-
Hey Guest!
British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!**Upgrade Now**
(PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
TR2/3/3A TR3 Radiator Rehab
- Thread starter Jprmm15
- Start date
Share this page
Offline
MGTF1250Dave
Jedi Knight
Offline
Aloha,
Your radiator needs to do two things, hold coolant without leaking at operating pressure (4 PSI with standard radiator cap or 7 PSI if you use a TR4 radiator cap) and effectively transfer heat.
First check for cracks where the long filler neck attaches to the upper tank. Also inspect any dents in the tanks for possible leaks. Most radiator shops can pressure test your radiator for leaks, but advise them what the normal operating pressure is so they don't over pressurize it.
Thermal performance is often overlooked if the pressure test is satisfactory. Look closely at the small fins in the core to make sure they are not broken and are attached to the tubes. These fins take the heat from the tube and shed it to the air passing through the radiator.
Use the specialty radiator paint. The heavy coating from regular paints will tend to insulator the radiator so it retains heat.
If the core appears to be damaged most reputable radiator shops can re-core the radiator for less than a new replacement.
Your radiator needs to do two things, hold coolant without leaking at operating pressure (4 PSI with standard radiator cap or 7 PSI if you use a TR4 radiator cap) and effectively transfer heat.
First check for cracks where the long filler neck attaches to the upper tank. Also inspect any dents in the tanks for possible leaks. Most radiator shops can pressure test your radiator for leaks, but advise them what the normal operating pressure is so they don't over pressurize it.
Thermal performance is often overlooked if the pressure test is satisfactory. Look closely at the small fins in the core to make sure they are not broken and are attached to the tubes. These fins take the heat from the tube and shed it to the air passing through the radiator.
Use the specialty radiator paint. The heavy coating from regular paints will tend to insulator the radiator so it retains heat.
If the core appears to be damaged most reputable radiator shops can re-core the radiator for less than a new replacement.
TR3driver
Great Pumpkin - R.I.P
Offline
My suggestion would be to take it to a radiator shop and have them test it for pressure holding, flow and thermal efficiency. Servicing the radiator on a TR3 is a PITA once the front apron is installed, so it pays to do it right the first time. If it's basically in good shape, they can clean and paint it as well. My shop will do the pressure & flow tests for free, but you may have to pay for the thermal test.
I had a terrible overheating problem that was eventually traced to poor thermal efficiency; apparently the tubes were no longer in good thermal contact with the fins. But because of the unusual original design, where the tubes run through holes in the fins, the problem was not apparent on casual observation. A recore solved the problem permanently.
Last time I checked, a recore wasn't much cheaper than a new offshore reproduction. But I'm inclined to think the recore produces a better quality result, especially if they use a Modine core.
I had a terrible overheating problem that was eventually traced to poor thermal efficiency; apparently the tubes were no longer in good thermal contact with the fins. But because of the unusual original design, where the tubes run through holes in the fins, the problem was not apparent on casual observation. A recore solved the problem permanently.
Last time I checked, a recore wasn't much cheaper than a new offshore reproduction. But I'm inclined to think the recore produces a better quality result, especially if they use a Modine core.
Offline
The other factor is that the original top and bottom tanks (assuming they're not damaged) are often better quality than those on the reproduction radiators.TR3driver said:
Offline
Josh: check for a PM.
Everyone else: I got a chuckle last night when Josh PM'ed me to tell me that the car in question is the one I'd sold to his father-in-law last spring! Small world!
Everyone else: I got a chuckle last night when Josh PM'ed me to tell me that the car in question is the one I'd sold to his father-in-law last spring! Small world!
T
TRDejaVu
Guest
Guest
Offline
When I had mine recored last year, I watched them pressure test it to 21 PSI.