• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)

Timing Question

Share this page

P

podracer169

Member
Offline
Greetings,
I am finishing up a complete rebuild of my 3000 MKII motor. I have decided to bench fire the motor to make sure that everything is OK prior to installing it back into the car. On the bench I have great spark and correct static timing, but I can seem to get it to even cough. I am starting to think that it’s timed 180deg wrong on the cam. Does anyone know what valves are open at TDC?

Steve
 

Attachments

  • 20210123_095911.jpg
    20210123_095911.jpg
    53.7 KB · Views: 141
  • 20210123_095735.jpg
    20210123_095735.jpg
    55.7 KB · Views: 136
  • 20210123_095601.jpg
    20210123_095601.jpg
    45.7 KB · Views: 125
  • 20210123_095427.jpg
    20210123_095427.jpg
    44.8 KB · Views: 137
  • 20210123_095139.jpg
    20210123_095139.jpg
    45.4 KB · Views: 128
  • 20210123_094857.jpg
    20210123_094857.jpg
    63.5 KB · Views: 127
  • 20210123_074454.jpg
    20210123_074454.jpg
    56.1 KB · Views: 135
  • 20210123_073848.jpg
    20210123_073848.jpg
    44.6 KB · Views: 133
  • 20210123_072511.jpg
    20210123_072511.jpg
    50.2 KB · Views: 135
  • 20210123_071911.jpg
    20210123_071911.jpg
    43.9 KB · Views: 130
  • 20210118_125621.jpg
    20210118_125621.jpg
    53.2 KB · Views: 149
  • 20210118_125308.jpg
    20210118_125308.jpg
    50.1 KB · Views: 133
I hope this will help.. did you at any time remove the pin from the shaft at the bottom of the distributor? and possably put the dog I beleive they call it, back 180deg off. I have done this... as soon as I changed it the engine started right up.
I'am not sure of which piston is tdc on your engine. I belive its always the #1 on 4 cyl
 
<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by podracer169:
Greetings,
Does anyone know what valves are open at TDC?
Steve<hr></blockquote>

Steve,

Not exactly sure what you mean but - with cylinder #1 on TDC firing stroke, both valves on #1 will be closed. At the same time, cylinder #6 will be on TDC exaust stroke. The valves on #6 will be almost closed, but both just slightly open.

D
 
Pod Racer,

Probably 180 out. Pull the lower distributor dog and spin it one flat. Varoom!
 
Congrats on the start up!!The big 6 does sound mean with open headers.
Did you install the trick rear main seal conversion while you were at it?? its cool an do-able. Skip the pre-done backplate(do your own)the rest is easy unless your fingers are too fat....I had to get a kid to install the lipspring onto the seal. Good luck on the tranny!!
MD(mad dog)
 
Back
Top