Hi Guest!
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
I thought that I would share my success with everyone because it saved me about $120.
As you know the most common failure on the Smiths Dual gauge is the Temp side. This is usually due to a broken capillary tube. When this tube is kinked or broken the Ether in the tube either escapes or can no longer apply pressure to the Bourdon tube inside of the gauge head. If your gauge looks good cosmetically and the Bourdon tube mechanism is undamaged the cost for repair from Hollywood Speedometer is about $120 plus shipping. You can test your head unit with simple air pressure applied to the sensor tube(s); if the needles move then your head unit should be ok. With these instructions you can repair it yourself with the bulb and tube from a $16.99 generic temp guage from your local auto parts store and about an hour of your time.
Tools Required:
1. Wire cutters
2. Soldering Iron
3. Solder
4. Small length of brass tube, roughly 1/16-3/32 ID
5. Bowl filled with crushed ice
6. Metal tin full of boiling water
7. New generic Temp gauge. Approx $16.99 from local auto parts store.
Instructions:
1. Cut the existing capillary tube approx 12 inches from the rear of the gauge. Remove about 2 inches of the protective spring material, this will give you room to work.
2. Test Bourdon tube mechanism with a small amount of air pressure to make sure that the needle does move.
3. Immerse the new temp gauge bulb in bowl of ice while we perform the rest of the steps to get the Ether as inert as possible.
4. After successfully testing the old gauge clean any old grease and grime off of the old capillary tube and prepare it for soldering. Make sure that the hole in the tube is open by using a small sharp object such as a sturdy straight pin.
5. Slide the short piece of brass tube over the capillary tube. Insert the capillary tube a little less than half way.
6. Solder the tubes together but be careful not to let to much solder get into the tube as it could clog the capillary.
- These next few steps must be performed pretty fast so that the Ether doesn’t have time to escape from the new gauge.
7. New Gauge- Cut the protective spring in two places approx 2 inches apart.
8. Cut through the capillary tube at the cut int he spring closest to the gauge and immediately place your finger over the end of the tube. You should smell a small amount of Ether in the air as it will begin to evaporate.
9. Using the small sharp object quickly inspect the end of the tube to make sure that its open.
10. Prepare the end for soldering by scuffing with a piece of scotch brite pad.
11. Quickly insert the new capillary tube into the small brass patch tube and immediately solder.
12. Inspect solder joints for a complete seal.
-Time to test and calibrate
13. Place the new bulb into the bowl of hot or boiling water. The needle on the gauge should begin to move immediately.
14. If the water is boiling wait for the needle to stop rising and reposition at approx 212deg.
A few words about safety!
Ether is HIGHLY flammable so make sure that no open flames are present during this repair. DO NOT use a torch for the soldering! Ether fumes are also very toxic. Avoid breathing in the fumes and work in a well ventilated area.
As you know the most common failure on the Smiths Dual gauge is the Temp side. This is usually due to a broken capillary tube. When this tube is kinked or broken the Ether in the tube either escapes or can no longer apply pressure to the Bourdon tube inside of the gauge head. If your gauge looks good cosmetically and the Bourdon tube mechanism is undamaged the cost for repair from Hollywood Speedometer is about $120 plus shipping. You can test your head unit with simple air pressure applied to the sensor tube(s); if the needles move then your head unit should be ok. With these instructions you can repair it yourself with the bulb and tube from a $16.99 generic temp guage from your local auto parts store and about an hour of your time.
Tools Required:
1. Wire cutters
2. Soldering Iron
3. Solder
4. Small length of brass tube, roughly 1/16-3/32 ID
5. Bowl filled with crushed ice
6. Metal tin full of boiling water
7. New generic Temp gauge. Approx $16.99 from local auto parts store.
Instructions:
1. Cut the existing capillary tube approx 12 inches from the rear of the gauge. Remove about 2 inches of the protective spring material, this will give you room to work.
2. Test Bourdon tube mechanism with a small amount of air pressure to make sure that the needle does move.
3. Immerse the new temp gauge bulb in bowl of ice while we perform the rest of the steps to get the Ether as inert as possible.
4. After successfully testing the old gauge clean any old grease and grime off of the old capillary tube and prepare it for soldering. Make sure that the hole in the tube is open by using a small sharp object such as a sturdy straight pin.
5. Slide the short piece of brass tube over the capillary tube. Insert the capillary tube a little less than half way.
6. Solder the tubes together but be careful not to let to much solder get into the tube as it could clog the capillary.
- These next few steps must be performed pretty fast so that the Ether doesn’t have time to escape from the new gauge.
7. New Gauge- Cut the protective spring in two places approx 2 inches apart.
8. Cut through the capillary tube at the cut int he spring closest to the gauge and immediately place your finger over the end of the tube. You should smell a small amount of Ether in the air as it will begin to evaporate.
9. Using the small sharp object quickly inspect the end of the tube to make sure that its open.
10. Prepare the end for soldering by scuffing with a piece of scotch brite pad.
11. Quickly insert the new capillary tube into the small brass patch tube and immediately solder.
12. Inspect solder joints for a complete seal.
-Time to test and calibrate
13. Place the new bulb into the bowl of hot or boiling water. The needle on the gauge should begin to move immediately.
14. If the water is boiling wait for the needle to stop rising and reposition at approx 212deg.
A few words about safety!
Ether is HIGHLY flammable so make sure that no open flames are present during this repair. DO NOT use a torch for the soldering! Ether fumes are also very toxic. Avoid breathing in the fumes and work in a well ventilated area.
