Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Offline
I have installed 3 point lap/shoulder belts using the factory mounting points on my BJ7. In spirited driving, like in my sig pic, the shoulder belt slips off my shoulder and ends up around my arm. Anyone have a solution?
-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Slipping Shoulder Belts
- Thread starter HealeyRick
- Start date
Share this page
Offline
Clip it to your helmet?
Offline
I use 3 point belts with a twist. The shoulder harness is actually a "Y" , with two over the shoulder webs that meet at the waist and are sewn together at the vertex of the "Y" just behind my neck. The single web then goes through a small slot I cut in the back vertical bulkhead just a bit below the top of my shoulders when I sit. It terminates with a fitting that is bolted to the bulkhead visible in the boot. It keeps the shoulder routing at shoulder height to avoid the compression of a low attachpoint in the unfortunate event of an accident. Here are some photos. They are a little embarrassing because of how dirty they look. I have a farm and here in the Sacramento Valley it is either mud season (if we're lucky) or serious dust season. I keep the car in the hangar I used to keep my airplane in. When I used to take off it looked like a JATO launch because of the dust. I gave up on constant cleaning and now just clean it up before a drive. Even then I
can't make it to the end of our gravel driveway without the car looking like it has been parked in the airport lot for months and has been abandoned.
can't make it to the end of our gravel driveway without the car looking like it has been parked in the airport lot for months and has been abandoned.bob hughes
Luke Skywalker
Offline
Make sure that the clip bit is down low at the tunnel so that the belt is right over your lap and the rest is over your shoulder and across the body, then tighten it up!
If you are racing then a four pointer would be better.
Not sure why you would be wearing a helmet on ordinary roads though, surely you are driving safely :wink-new: however spirited you driving is.
Bob
If you are racing then a four pointer would be better.
Not sure why you would be wearing a helmet on ordinary roads though, surely you are driving safely :wink-new: however spirited you driving is.
Bob
OP
Offline
I found a cure: "Strap Gummy" a silicone strip that sticks to the back of the belt. Cheap, works great and I didn't have to screw a bracket into the back of the seat: https://www.amazon.com/gp/product/B00XTGBN6M/ref=oh_aui_detailpage_o01_s00?ie=UTF8&th=1
RAC68
Darth Vader
Offline
Hi Rick,
A while back a friend was complaining of having the same issue and, jokingly, I suggested he use the double clip hat tether he was waring to secure the sholder belt to the opposite shoulder of his shirt. He responded that "this sliding belt is such a PIA its worth a try." When meeting a few months later, he was still using the hat tether to stop the belt from slipping off his shoulder and suggested we promote them on eBay as Belt Tethers.
Hope this helps,
Ray(64BJ8P1)
A while back a friend was complaining of having the same issue and, jokingly, I suggested he use the double clip hat tether he was waring to secure the sholder belt to the opposite shoulder of his shirt. He responded that "this sliding belt is such a PIA its worth a try." When meeting a few months later, he was still using the hat tether to stop the belt from slipping off his shoulder and suggested we promote them on eBay as Belt Tethers.
Hope this helps,
Ray(64BJ8P1)
OP
Offline
Thanks, Ray. I talked to two other Healey friends last week that were having the same problem. The "strap gummy" so far is working good. You've given me a good idea, though, and I'll start selling them as Shoulder Belt Gummy and kick 10 percent back to you. Maybe we could buy a pint or two with our profits.