-
Hi Guest!
You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
TR2/3/3A Distributor Clamping Plate Studs
- Thread starter af3683
- Start date
Share this page
TR3driver
Great Pumpkin - R.I.P
Offline
The coarse threads on those studs are pretty short as I recall. Might not be enough room to get two nuts on there.
If that is the problem, take a single nut and cut through one side of it. A Dremel tool with abrasive cutoff blade makes short work of this, but it can be done with a hacksaw and patience.
Place the split nut on the threads, then clamp it there with vise grips or your bench vise.
After removing the other nut, and releasing the pressure from the split nut, it should come off easily.
If that is the problem, take a single nut and cut through one side of it. A Dremel tool with abrasive cutoff blade makes short work of this, but it can be done with a hacksaw and patience.
Place the split nut on the threads, then clamp it there with vise grips or your bench vise.
After removing the other nut, and releasing the pressure from the split nut, it should come off easily.
TR3driver
Great Pumpkin - R.I.P
Offline
I'm not familiar with Arrow Bolts, but I didn't have any luck finding 1/4" mixed thread studs at MMC, MSC or Grainger.
You may be stuck either using 1/4-20 on both ends (but I really hate installing hardware with the wrong thread) or making your own. Making your own does involve some tools and time, but isn't difficult. And its easy to start over if need be.
You may be stuck either using 1/4-20 on both ends (but I really hate installing hardware with the wrong thread) or making your own. Making your own does involve some tools and time, but isn't difficult. And its easy to start over if need be.
Offline
martx-5
Yoda
Offline
McMaster shows a few. Don't know if any of the lengths will work.
[h=3]Hex Drive Threaded Rods[/h]
A hex drive on one end allows these rods to be turned with a hex key for ease of installation. Use them to connect parts with coarse threads to parts with fine threads. They're high-strength black-oxide steel and corrosion resistant in dry environments.
For technical drawings and 3-D models, click on a part number.
[h=3]Hex Drive Threaded Rods[/h]
A hex drive on one end allows these rods to be turned with a hex key for ease of installation. Use them to connect parts with coarse threads to parts with fine threads. They're high-strength black-oxide steel and corrosion resistant in dry environments.
| Thread (A) | Thread (B) | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| Size | Lg. | Size | Lg. | Lg. | Drive Size | Tensile Strength, psi | Hardness | Each | |
| Black-Oxide Alloy Steel | |||||||||
| 1/4"-20 | 3/8" | 1/4"-28 | 7/16" | 1" | 3/32" | 150,000 | Rockwell C38 | 94358A110 | $3.02 |
| 1/4"-20 | 3/8" | 1/4"-28 | 3/4" | 1 1/4" | 3/32" | 150,000 | Rockwell C38 | 94358A120 | 3.43 |
| 1/4"-20 | 3/8" | 1/4"-28 | 1" | 2" | 3/32" | 150,000 | Rockwell C38 | 94358A130 | 3.84 |
| 1/4"-20 | 3/8" | 1/4"-28 | 1" | 3" | 3/32" | 150,000 | Rockwell C38 | 94358A140 | 4.54 |