but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Offline
-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Caving In [5-speed conversion for BN2]
- Thread starter roscoe
- Start date
Share this page
Online
Re: Caving in
That's a Series I E-Type bezel, available from most of the Jag stockists. When moving my headlight dipper to the dash, I used an extended toggle to make it easier to find in the dark.
I
I really would like to have an MGA = Flash-to-pass switch but very hard to find and expensive when you do: https://mgaguru.com/mgtech/accessories/at113.htm
That's a Series I E-Type bezel, available from most of the Jag stockists. When moving my headlight dipper to the dash, I used an extended toggle to make it easier to find in the dark.
I really would like to have an MGA = Flash-to-pass switch but very hard to find and expensive when you do: https://mgaguru.com/mgtech/accessories/at113.htm
HealeyPassion
Jedi Warrior
Offline
Re: Caving in
Rick.... flashing to pass isn't something I seem to have many opportunities to use
eaceful:
Rick.... flashing to pass isn't something I seem to have many opportunities to use
eaceful:
Online
Re: Caving in
Steve,
Instead of trying to eke more power out of those lorry motors, drop in a V8 and your passing opportunities will increase immensely.
Rick.... flashing to pass isn't something I seem to have many opportunities to use
Steve,
Instead of trying to eke more power out of those lorry motors, drop in a V8 and your passing opportunities will increase immensely.
Online
My switch is a three-position one: Up for high, center for low and down is spring-loaded for flash-to-pass. Because it's in the O/D switch hole it doesn't need to be long. It operates relays.
HealeyPassion
Jedi Warrior
Offline
Re: Caving in
Rick, you know funny you should mention that... a couple of my friends have been telling me that for years!! .... and yet ... I keep on trying to make a silk purse out of a sows ear ... ah well ... I enjoy the challenge!
Steve
Steve,
Instead of trying to eke more power out of those lorry motors, drop in a V8 and your passing opportunities will increase immensely.
Rick, you know funny you should mention that... a couple of my friends have been telling me that for years!! .... and yet ... I keep on trying to make a silk purse out of a sows ear ... ah well ... I enjoy the challenge!
Steve
OP
Offline
This is in response to Steve G's question about the original BN2 clutch lever pivot, welded on stud versus a Jule frame. The master cylinder holding bracket that came with my kit doesn't come close to fitting due to inadequate clearance between the edge of the oil pan where it mates with the block. I'll be doing something similar to Dave Deamer most likley but I will talk to Pete Delaney tomorrow and see what he says.
twas_brillig
Jedi Knight
Offline
Welcome to the dark side! I put a small clock (from a motorcycle shop) in place of the O/D switch. I was thinking of leaving the switch in place, and labelling it 'Nitrous'...
Doug
Doug
Bob_Spidell
Yoda
Offline
I always wanted a "Passenger Ejection Seat" switch.
Offline
This is better. I can carry extra missiles and a lot easier than replacing a seat every time I use it.
