• The Roadster Factory Recovery Fund - Friends, as you may have heard, The Roadster Factory, a respected British Car Parts business in PA, suffered a total loss in a fire on Christmas Day. Read about it, discuss or ask questions >> HERE. The Triumph Register of America is sponsoring a fund raiser to help TRF get back on their feet. If you can help, vist >> their GoFundMe page.
  • Hey there Guest!
    If you enjoy BCF and find our forum a useful resource, if you appreciate not having ads pop up all over the place and you want to ensure we can stay online - Please consider supporting with an "optional" low-cost annual subscription.
    **Upgrade Now**
    (PS: Subscribers don't see this UGLY banner)
Tips
Tips

BJ8 Vacuum Advance - disconnected -RIGHT - when setting total advance??

jjs64bj8

Senior Member
Offline
I just need to get expert clarification. The vacuum advance for a BJ8 (64 PH II) is to be disconnected and plugged when setting the maximum advance of around 35 degrees at >3000RPM and 15 degrees at 600-700 RPM at idle, tickover or whatever it is called.

YES??

Thanks,

So follow up question with vacuum advance connected and working properly what advance should one see at idle and at >3000RPM??
 

Jim 58 BN6

Jedi Trainee
Offline
Well, expert is a relative term, but in general, here's what I would do:

1. Vacuum line removed from the distributor, and the line plugged: Set the timing at idle, then check the distributor's mechanical advance at >3000RPM.
2. Reattach the vacuum line: Check the TOTAL advance at >3000RPM, which is the sum of the idle setting, mechanical advance and vacuum advance.

I hope someone can chime in with a Healey specific answer to your second question, but I think the total distributor advance at >3000RPM is about 20 degrees, and that's in addition to the idle setting of 15 degrees, so 35 degrees total. If the vacuum advance line is connected when you check the timing at idle, then it might give you an incorrect, slightly higher reading. GL, Jim
 
OP
J

jjs64bj8

Senior Member
Offline
Follow up,

Got a cheap Harbor Freight Advance timing light for $29.99 less the 20% and free flashlight, to double check my 40 year old Craftsman light. The HF light work very well (at least for now).

I have 15 deg at 650 RPM vacuum disconnected, and around 35 deg at over 3000 rpm vacuum disconnected and plugged.

With vacuum advance back in service, I still have around 15 deg at idle, and now just over 40 at over 3000 rpm.

Do these numbers make sense for a freshly rebuilt 64 BJ8.

Thanks
jjs64bj8
 

Jim 58 BN6

Jedi Trainee
Offline
I think they're close to the specifications. At this point, drive it, and see if you experience any pinging when the engine is under load. If it pings, retard the timing a couple of degrees at a time until the pinging stops. The timing shouldn't require much readjustment at your current setting. If you can only get low-octane gas, then you may need to run it with the timing a bit retarded anyway. This technique is simple, and has always worked for me. Jim
 

steveg

Yoda
Gold
Country flag
Offline
...With vacuum advance back in service, I still have around 15 deg at idle, and now just over 40 at over 3000 rpm.

The factory manual: General Data pg 12 says "Maximum Advance.....35 deg (Crankshaft) B.T.D.C" -- therefore I think you should retard your distributor slightly to 35 degrees with the vacuum connected.

Assuming since they didn't say disconnected vacuum at the maximum advance - that it should be connected as per normal driving.

The stock pulley is 6.25" D. Therefore 35 degrees is 1-7/8" BTDC; 32 deg is 1-3/4 BTDC. I trust my old Sears non-adjustable timing light more than the HF adjustable which had a floppy knob on it.
 
OP
J

jjs64bj8

Senior Member
Offline
I rechecked everything and both the HF light and the old Sears match.

The final numbers are

Dwell 33 deg point gap .016 engine totally fresh with less than 200 mi since rebuilt.

Vacuum disconnected and plugged Idle (650rpm) 15 deg BTDC >3000rpm 31-32 deg
Vacuum connected Idle between 15-16 deg >3000 rpm 35-36 deg

Dizzy is a 25D

Thanks
jjs64bj8
 
Similar threads
Thread starter Title Forum Replies Date
Patrick67BJ8 BJ8 Intake manifold Booster & Vacuum Hookup threads sizes. Austin Healey 2
5 BJ8 cam idle vacuum Austin Healey 6
1 BJ8 History Trace Austin Healey 7
Patrick67BJ8 Wanted Looking for a used BJ8 switch panel. Austin Healey Classifieds 5
D BJ8 Top Installation Detail Austin Healey 3
B BJ8 Rear Backrest Hinges Austin Healey 4
S Wanted WTB: 3.5 ratio diff/pumkin for '67 BJ8 Healey 3000 Austin Healey Classifieds 0
AUSMHLY BJ8 Trans Cover Carpet Austin Healey 7
nitro BJ8 Engine Design Austin Healey 1
AUSMHLY BJ8 Carpet and Snaps Austin Healey 2
Overdrive45 BJ8 Interior Trim Austin Healey 8
nitro BJ8 Production Year Austin Healey 6
WHT BJ8 Rear Seat Surround Drain Tube Grommets Austin Healey 0
B BJ8 Seat Sliders Austin Healey 4
B For Sale 1967 Metallic Golden Beige MKIII BJ8 Numbers Matching - The Real Deal Austin Healey Classifieds 0
F Wanted BJ8 Engine Block Austin Healey Classifieds 1
BoyRacer For Sale BJ8 disk wheel hubs, spindles & calipers Austin Healey Classifieds 0
AUSMHLY BJ8 Rear Seat Squab Austin Healey 0
AUSMHLY BJ8 Differential Oil Change Austin Healey 6
S SOLD!! For Sale 1964 AH 3000 MkIII BJ8 Phase 1 Austin Healey Classifieds 2
Patrick67BJ8 BJ8 Factory Hardtop Rear Window Austin Healey 6
AUSMHLY BJ8 Clutch Pressure Plate, Old vs New Austin Healey 4
AUSMHLY BJ8 Clutch Fork Bush Replacement Austin Healey 5
AUSMHLY BJ8 Cylinder Head Installation Austin Healey 6
LAW75 BJ8 Brake Lines Austin Healey 2
AUSMHLY BJ8 Clutch Pressure Plate Brand Preferences Austin Healey 3
BoyRacer For Sale BJ8 spindles & disc wheel hubs Austin Healey Classifieds 0
G Wanted BJ8 Tonneau Cover Austin Healey Classifieds 0
Cutrog1 For Sale Healey 3000 BJ8.... a restoration saga Austin Healey Classifieds 0
AUSMHLY BJ8 Overdrive Oil Passages Austin Healey 2
Scotsman Wiring Diagram for 1966 BJ8 Austin Healey 3
A For Sale 1966 3000 Healey Blue BJ8 Austin Healey Classifieds 3
S BJ8 Front Side Lamp/Turn Signals Austin Healey 1
B BJ7/BJ8 Door Check Straps Austin Healey 10
B BJ8 Hood Bow and Seal Austin Healey 5
Mickey Richaud Wanted Wanted: BJ8 Seat Track Sets (Both Sides) Austin Healey Classifieds 5
Scotsman BJ8 Intake Manifold Differences Austin Healey 4
AUSMHLY Laygear End Float BN1-BJ8 Austin Healey 2
C For Sale BJ8 original dash Austin Healey Classifieds 3
LarryK BJ8 Parts or Project Car For Sale in St. Louis Austin Healey 3
B BJ8 Centre Console Chrome Strips Austin Healey 5
B Wanted Chrome strips centre console BJ8 Austin Healey Classifieds 0
AUSMHLY BJ8 Cylinder Head Re-Torque Austin Healey 26
AUSMHLY BJ8 Transmission Gasket Austin Healey 0
AUSMHLY R & R BJ8 Transmission Bearings Procedure Austin Healey 1
AUSMHLY BJ8 transmission 3rd gear chipping Austin Healey 0
AUSMHLY BJ8 transmission mainshaft bearing force needed to install/remove Austin Healey 1
AUSMHLY BJ8 Transmission Oil Capacity Austin Healey 1
6 BJ8 Headlamp Wiring Austin Healey 1
H Wanted Need Spare tire rod BJ8 Austin Healey Classifieds 1

Similar threads

Top