• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
Tips
Tips

100/6 tuning and suspension ugrades advice

Share this page

L

Leew

Senior Member
Offline
I have a pretty standard 58 100/6 which I've owned for a couple of years.
I've done very little to it other than a general service of the carbs, plugs and points
I've installed a new exhaust, as well as seat belts a roof and some heatshield
I also had the gearbox and overdrive rebuilt by Hardy engineering in Leatherhead
I think it time I start to improve the handling and performance
I was thinking to uprate the rear springs to the Dennis Welch 8 leaf spring as well as change the front shock absorbers https://www.bighealey.co.uk/performance-parts/austin-healey/healey-suspension/rear-suspension
https://www.bighealey.co.uk/performance-parts/austin-healey/healey-suspension/rear-suspension?page=2
I was also thinking to change the distributor and add some nice new plug leads https://www.bighealey.co.uk/perform...l-with-tacho-non-vac-positive-earth-celi102ep
https://www.bighealey.co.uk/perform...on/silicone-plug-lead-set-6-cyl-black-celi153
However, I am open to suggestions
I'm a weekend driver, but do like to run it on the edge, even though we live in a nanny state nowadays where driving at speed is concerned
Any comments and thoughts appreciated
L
 
It’s not entirely clear what your aim is. Are you trying to improve the handling, the performance or both? In isolation I see no point in updating the rear springs in a normal road car. Replacing the distributor, if it is working properly also seems to be unnecessary.

A simple and cheap handling upgrade is to lower the front suspension with spacers and fit a thicker anti roll bar, but I would first decide exactly what it is you are trying to achieve, a fast road car set up for instance.
 
Here's the upgrades I have done to my '57 100/6 (BN4). It came with a 3000 engine, but everything would apply to the 2.6L.
Performance:
  • Denis Welch fast road aluminum head with compression set for 91 octane (US)
  • Denis Welch DW8 cam & tappets. This requires pockets in the top of the block for valve clearance.
  • Denis Welch aluminum oil pan
  • Oil cooler
  • BJ8 intake manifold with two HD8 SU carbs
  • Crane electronic ignition
  • Recored radiator (an aluminum radiator would probably be less expensive now)
  • Rally vents to exit hot air
  • Exhaust headers
  • Side exit exhaust
  • Disc brakes all around with separate front & rear circuits (Nissan 1200 tandem master cylinder, Girling 16PE in front and Jaguar in rear. If you do this, ask Steve about how to make the parking brake work again.)
  • Move overdrive switch to gearshift knob. (Put headlight dip switch in place of old overdrive switch and put dead pedal in place of old dip switch.)

Handling:
  • Lowered front by ~3/4"
  • Denis Welch front heavier anti-sway bar, 7/8" IIRC
  • Polyurethane bushings for the anti-sway bar links
  • Fabricated anti-sway bar links using grade 8 bolts and 1/8" pipe. The heavier anti-sway bar will snap the stock links.
  • Adjustable camber top kingpin bushings. Camber is now -1.5 deg.
  • Anti-tramp bars at the rear
  • New stock rear springs (old ones were sagging)
  • Polyurethane bushings for the Panhard rod
  • Dayton 72-spoke wire wheels with 195/65R-15 tires


For Marin-Sonoma.jpg
 
Back
Top