-
Hi Guest!
You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
tr3a
-
A
TR2/3/3A Clutch Question
Hello! A bit of background, I purchased a 1960 Triumph TR3 as a project for myself to work on. The car is not currently drivable and I am going through everything to get it there. I removed the clutch slave cylinder to rebuild it, when I found that the clutch shaft could be easily moved by... -
G
TR2/3/3A TR3A Electrical Quirks, Flasher, Wipers and Fuel Guage
Armed with a forum suggested wiring diagram I succeeded in rewiring my 59 TR3A, or I thought so.... I have traced all wires, checked continuity and grounds, installed a new flasher and tested all lights independently. I was tipped off that the wiring between flasher and wiper motor must be... -
G
TR2/3/3A Wiring diagrams anyone??
Do any readers have access to a correct wiring diagram for a late 59 Triumph TR3A (Comm no. is 65421) I have seen several conflicting diagrams and having recently replaced my harness I am regularly blowing the A1 fuse. I suspect it is related to the potential need to ground the fuel gage or... -
T
TR2/3/3A Girling Brake/Clutch Master Cylinder [slant port] Variations?
My preference is to reuse the old master cylinders for my '59 TR3A and send them to Apple Hydraulics for sleeving. In taking a closer look, they are not identical castings. One is stamped "Girling 75" and the other simply "Girling" in smaller letters. Both have (as best as I can make out) the...- Tropical TR
- Thread
- girling master cylinder tr3a
- Replies: 6
- Forum: Triumph
-
T
TR2/3/3A Wanted: Tr3a lft frnt brake caliper
Anyone know where I can obtain one? Thanks. -
T
TR2/3/3A TR3A "TRIUMPH" Letter Versions
I am restoring my TR3A (TS52910L, EB# 51292, produced in May 1959) and hope I can get more clarity as to whether older or later style TRIUMPH letters should be used below the front badge. When I got the car, it had the smooth shiny (albeit pitted) later style letters mounted. But that doesn't...- Tropical TR
- Thread
- apron letters letters tr3a
- Replies: 18
- Forum: Triumph
-
A
TR2/3/3A Tr3 Seat Belts
Hello All, I am nearing the end of getting my 61 Tr3 back on the road after 20+ years. The previous owner had the seat belts attached to the heel board, aka the vertical panel directly behind the seat. My question is for those of you owners that have installed belts at this location on post 60K... -
A
TR2/3/3A Correct Coil for petronix ignition tr3A
Hello all, I have made it to the point in my rebuild of installing my new petronix Positive ground ignition, at the same time I ordered the ignition I got the petronix flamethrower coil. I am questioning now whether that is the correct Ohmage coil to use with the ignition. Petronix paperwork... -
A
TR2/3/3A Tr3A Oil Priming
Hello all, I have just finished rebuilding my Tr3 engine and am attempting to prime the oil system. I made a spade tip rod and chucked it up into a drill. spinning it counterclockwise ate about 750rpm i get oil to the block galleys and through the pressure tube. but no oil is appearing at the... -
A
TR2/3/3A First Time TR3A Owner with stuck engine
Hello All, I have recently picked up an all original 61 Tr3a with 54k miles that has been sitting in storage for 20+ years. Upon getting it home and in the garage i set to work rebuilding the brakes and filling what little rust I have in the floorpans. The only holdup now seems to be the...