• Hey Guest!
    British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)

LONGBRIDGE cars SOFT TOP -MOD safe water seapage

Share this page

andrea

andrea

Jedi Knight
Offline
Interesting and easy to do MOD MOD TOP1.jpgit also finish well the ends of cockpit trim on longbridge100_1338.jpg
anyone applied it? I am care about the door aluminiumMOD TOP2.jpg trim conflict
Cheers
 
Andrea - I have not tried it, But I do have a question of your first photo. What information do you have about it? It appears to be an Ivory exterior with a red interior with cream piping. According to the Concours Guide for 2012, this piping on the door shut pillar should be cream and not black as shown in the photo. Do you have any informatioon you can share about this question.

as always, thanks for the great photos for those of us with the Longbridge BN4

jim:driving:
 
scan0003.jpgHi Jim
this is the only other photo of the MOD that I have find
from 100 Six Derek site https://www.healeysix.net/Longbridge2.htm photos are from Rich Chrisler, and here I have find a 3rd car with this modMOD top3redinterior.jpg
NOTE on my previos thread car are TWO, one white and one black- on the third photo the car are black with black pipe(the light on the photo mix up)
the presence of the MOD on a 3rd car reveal tha this mod was extensively used on 100 six Longbridge cars
Cheers
 
The comment I read was that these deflector things were fitted when a factory hard top was optioned. Are you having leakage problems? Andy.
 
Hi Andy
No problem at the moment,
BUT the reason is that my car never are ON THE ROAD again IMGP1960.jpg and yes I have also the HTop
and my zone in Italy are subject to heavy rain in Springtime and Fall
so i am interested in this MOD-
my project is to make one aluminium prototype
and then a stainless steel couple
Cheers
 
Andrea - put me on the list for a set of these after they are made, so my hardtop will be complete. It is due for a new paint job, since I painted it over 25 years ago.

jim:driving:
 
Andrea- your car is looking in very much the same stage as mine right now. I also have a hardtop that was purchased by the first owner around 1960, three or so years after he bought the car. I'll be interested in your mod too. Andy.

602158_10151336809274212_502676534_n.jpg
 
healey106 said:
Andrea - put me on the list for a set of these after they are made, so my hardtop will be complete. It is due for a new paint job, since I painted it over 25 years ago.

jim:driving:
Click to expand...
Hi Jim and Andy
I must wait to fit the doors, and control if I have the space to fit the MOD, I hope to do it this week
Cheers
 
Here my prototype,
IMGP2006.jpgI have decided to work with copper, malleable and easy to chromeIMGP2007.jpgIMGP2008.jpgMODws - 1..jpg and the sketch
one more useful photo fro rearIMGP2012.jpg
for few days I have no access to the doors, Mauro works on them
so I haven't full tested the piece but appear to be good
Cheers
 
Hi Jim
Work in progress(same prototype development)IMGP2012.jpg
MOD TOP12.jpgsimply painted white primer and chrome sprayed
MOD TOP13.jpg
in situ-
NOW I must test the door look- and the definition of the lip that is screwed to the Door Dust Seal- and conflicts with aluminium door covers
Cheers
 
Last edited:
More progress but NOT definitive,with same prototypeMOD TOP15.jpg

NOW one new prototype can be developed:
a)the under screwing lip is in good position to be screwed with the same screw that fasten the Door dust seal
b)the hole for upper screw ( to cockpit aluminium and fender)can be positioned
c)the gap from fender must be better covered- and black vinyl seal junction join up
 
Here the 2nd prototype draft with measurements, in mmprotmod2 - 1.jpgRH or LH side depends from the face worked
and the cut of the same, precision is NOT neededMOD TOP16.jpg
after the hammer and gridding work, the RH prototype is ready- difficult is to make the TWO pieces RH and LH equalsMOD TOP17.jpg
not a lot of work just few minutes with hammer on a hard wood piece-
cooper is easy to work and to chrome or also silver plated
NOTE: my measurement can be different for your cars- i have one obscure GAP of 2mm from my shroud and cockpit trim aluminum at RH and LH side-
SO my measurement 25mm can be more large, than normal cars and 23mm can be the right measure
Cheers
 
NEWs from the MOD prototype -after, I have finished my rear panels. I am noticed that there are not space from my aluminium trim on the door and the finisher plate ( I have hammered (gently)it to permit to my doors will be opened and closed) panelr1.jpg so the prototype is in front of me, waiting a solution
 
Back
Top