-
Hi Guest!
You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
TR2/3/3A Thinking of upgrading to 86 or 87 mm liners and pistons....
- Thread starter karls59tr
- Start date
Share this page
buy a head gasket like this. Not much else will change.
bpnorthwest.com
Head Gasket Big Bore 87mm to 90mm LUCAS
Your One Stop Shop For All Your British Automotive Parts. Order Online Today! We Have The British Auto Parts That You Are Searching For. Order Today! No Sales Tax. Fast, Courteous Service. Rich Selections. Order Hard To Find Parts. Family Owned & Operated. Fast Shipping.
bpnorthwest.com
Looks like a good head gasket. Do you mean not much else will change in terms of horsepower and performance?buy a head gasket like this. Not much else will change.
Head Gasket Big Bore 87mm to 90mm LUCAS
Your One Stop Shop For All Your British Automotive Parts. Order Online Today! We Have The British Auto Parts That You Are Searching For. Order Today! No Sales Tax. Fast, Courteous Service. Rich Selections. Order Hard To Find Parts. Family Owned & Operated. Fast Shipping.
Unless your motor has some other issues that need attention,like smoking,low compression,valve job needed,head gasket leak etc, I would not take apart a good running motor for this slight displacement increase.
Now if you are in need of rebuild I think the 86mm are cheaper than 83mm and of course most would upgrade.
Tom
Now if you are in need of rebuild I think the 86mm are cheaper than 83mm and of course most would upgrade.
Tom
I put 87mm in my engine. I also had the luck to find an aluminum head with bigger valves already set for a real good price. The combo is a lot more HP. ( I don't know how much, but I can feel it and my friend says it is a lot more HP than his). I did not change the cam. I have HD6 SU carbs. Great little car.
Offline
You will have to upgrade the fuel due to better compression.(The 86 was always a factory option for the Tr3.)
I have always liked 87mm myself.When you do it, freshen up the low end and use the good bearings.
Also you can forget about using the hand crank only a gorilla can crank the larger pistols.
Mad dog
I have always liked 87mm myself.When you do it, freshen up the low end and use the good bearings.
Also you can forget about using the hand crank only a gorilla can crank the larger pistols.
Mad dog
OK i will go with 87mm. Upgrade the fuel in what way? Karl
Offline
Lets just say" Ethel" to drag and old saying out of the dust bin. As always the timing needs to be set
for the fuel getting consumed. The old school way is to warm up the engine, drive up a modest hill, and listen for
any detonation as you accelerate in 3rd. Advance the timing until there is just a little tiny bit, Now drop it back 2 deg, and lock it down.
You don't want any detonation,as it does real damage at speeds where it goes unnoticed.
One more trick on breakin, never lube the rings on install. They will seat in the first 60 seconds of running, otherwise
the can take months to stop using oil.
Mad dog
for the fuel getting consumed. The old school way is to warm up the engine, drive up a modest hill, and listen for
any detonation as you accelerate in 3rd. Advance the timing until there is just a little tiny bit, Now drop it back 2 deg, and lock it down.
You don't want any detonation,as it does real damage at speeds where it goes unnoticed.
One more trick on breakin, never lube the rings on install. They will seat in the first 60 seconds of running, otherwise
the can take months to stop using oil.
Mad dog
I see your point of not having to upgrade if it's not really necessary. I just had cylinder head work done and replaced the head gasket. That was the time to upgrade to the 87's but unfortunately I do not have a proper shop to do the work and I'm getting too old to crawl underneath and tap out the old liners. Anyway the car is running fine for the cool Fall weather we are having here so I'm just going to enjoy the ride for now. One thing I need to do next year is to replace the timing chain. Pretty sure it's worn and making noise. A fellow club member gave me a set of new gears from a project car he never used so I just need the chain. I'm fairly confident I can tackle this job but I'm a little intimidated about getting the chain set properly and not have it one tooth out? Any thoughts?
Offline
It's not just one tooth. The camshaft is timed to within 1/4 tooth. The procedure isn't simple and I would hate to have to do it with the engine in the car. As a minimum, I think it would be necessary to remove the radiator and grille. (I'm thinking TR4A here; not sure about the TR3).\
FWIW, here is my experience; > Engine Rebuild <
FWIW, here is my experience; > Engine Rebuild <
As mentioned above, the one problem I had with my last set of liners was the piston rings. The oil ring was the set of two thin springs, and a wavy piece in the middle. I have not had luck with that type of oil ring. I also think the liner sets have too much ring gap as sent from whatever factory they come from.
Thanks for he info.
I suggest anyone getting new liner and piston set measure carefully before install,not taking for granted that the manufacturer has got the fit right.
My replacement 86mm set from Moss last year had piston to liner clearances varying from .0035 top to .0015 bottom .So not only tight,but tapered.
I had my speed shop hone straight and round .0045.I tried to size myself with my lisle ridgid hone which works fine on my cast iron motorcycle cylinders but the liners were very hard and would have taken way to long so I sent them out.
I bought a very nice dial indicator bore gauge for around $70 ,but you will also need a 3-4" mic to go with it.My
Starrett snap gauges will be retired.
Tom
Last edited:
Offline
I simply copied the marks from my old gears. Easy if you make sure the old and new gears are facing the same way up, exactly line up the bolt holes on the cam gear (just put bolts thru the holes thru both gears), and make sure the teeth are exactly aligned. Crank gear is easy, only a few teeth so it is hard to screw up.
Bob
Bob
So it's not as complicated as I've been led to believe? That's good to know. Not clear on what you mean by "having the old and new gears facing up" but i guess if I had them in front of me I'd see what you mean. Where did you buy your chain the last time you replaced one? Is it better to get a chain where there is one link that separates? Karl