Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
I'm running a "mild street cam" on my TR3. I was told to run .016" for the valve clearance. The stock spec is .010" intake.....012" exhaust. Anyone running a modified cam? What do you set your valve gap at? I dont have the exact cam grind specs handy but I'll try to find it in my papers. Apparently its a very common cam grind for "street" to give the car some extra grunt.
-
Hey Guest!
British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!**Upgrade Now**
(PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
TR2/3/3A TR3...Mild street cam....valve gap?
- Thread starter karls59tr
- Start date
Share this page
martx-5
Yoda
Offline
"Who" told you to set the valve clearance at .016"?? If it was the cam grinder, then that's what you set it for. Each manufacturer has it's own specs for each grind. If it was your buddy down the street who told you to set it at .016", then I would call the cam grinder or whoever you got the cam from to verify what the clearance should be.
Well the cam grinder ,Shadbolt cams from Vancouver said to set the gap at .016" and I have no doubt he's correct. But are cam manufacturers familiar with 40 year old brit motors? I was wondering if any TR3 owners on this site had experimented with valve gap to find optimum gap and where they had there's set at.
Karl, As much as anything the larger gap assures that the points of opening and closing are matched as much as possible. Which is to say the more you close that gap the more likely you will encounter variations on the profile of the cam lobes. One intake might open a degree or more before another does. If you want to take the time to experiment pull your plugs, take all the gap out of the rocker arms on the backside of the cam lobes (just twist the adjustment screw very lightly till contact is made), use a dial indicator to detect open and closing, turn the engine over slowly by hand with the fan and mark the open and close points on the pulley. I used to use typing 'white out', that stuff's probably history. Out of four cams on the shelf in the garage, two ( an Isky and a Triumph D are pretty accurate though not perfect but the other two really do need that extra gap the allow all cylinders to breathe equally. On a rolling road dyno decades ago, we never saw anything in the way of significant output changes from making minor changes in the valve clearances.
Tom Lains
TS8651 & 58107
Tom Lains
TS8651 & 58107
So .016" for all intake and exhaust would be way better than the stock .010" that I set them at after the rebuild? My car had lots of power but I got the feeling that when I let off the gas it seemed to run rough. I have heard that at idle with a modified cam it will never idle smoothly. The car pulled strong after about 3000rpm. I've got about 100km. on the rebuild and new cam so I think in the Spring I'll open up the valve gap to .016" and see what happens. Karl
Simon TR4a
Jedi Knight
Offline
The cam in my TR4a is "not so mild", and Kent cams specifies clearances of 22 thou. intake and 24 thou. for the hotter exhaust valve.
It seems extreme, to the point I thought it might be a misprint and sent them an email to ask, but they confirmed it is correct.
Simon.
It seems extreme, to the point I thought it might be a misprint and sent them an email to ask, but they confirmed it is correct.
Simon.
