• Hi Guest!
    You can help ensure that British Car Forum (BCF) continues to provide a great place to engage in the British car hobby! If you find BCF a beneficial community, please consider supporting our efforts with a subscription.
    There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Subscribers don't see this gawd-aweful banner
Tips
Tips

PPG Paint?

Share this page

Bet I would walk right in and ask for some printed info.

PPG is good stuff, should be lots of written guidance.
 
I prefer PPG over the stuff I use. It costs a little more, but I'm thinking about switching back. Their High Solids Clear Coat goes on very smooth.
 
Bud,

PPG, DuPont, Acme, Valspar, etc. all make pretty good stuff. Pro painters always will have their favorites. They all prefer one over the other for various reasons.

I've used Kirker paints for a few projects and have been pretty satisfied. Much cheaper than the 'big name' paints, ez to work with and I guess I'm dumb enough about paints that I couldn't tell the difference between Kirker and the brand names anyway.

I'm not saying you'll win any concours prizes with the cheaper stuf but for an average, everyday driver they make a pretty nice product.

https://www.smartshoppersinc.com
 
Hehe,
Smart Shoppers. They are local to me. I used to buy a bunch of stuff from them.

Never tried that line of paint. Much of the paint preference will depend on what you learn on and how good your equipment is.

Here is what I've used lately (though I'm not happy with their clear coat).

https://www.matrixsystem.com/
 
I got started usingPPG paints several years ago because it seemed to be the favorite of most of the street rodders and those guys do some terrific finishes. Considering the results and the work involved, regardless of whose paints you use, I don't think I would use anything else. It's not the cheapest by any means but it just works and gives a great finish.

The steps I like are 1) metal prep, 2) DP series epoxy primer. 3) K200 surfacer (high build and catalyzed), 4) reduced DP epoxy for sealer and 5) DAU Deltron urethane topcoat. Unfortunately, I hear that Deltron is no longer available. I have not yet used the replacement but hope to later this year.
 
K200 is no longer sold in California. I have be spraying Concept single stage for a few years now and am very happy with the finish. Like that picture of your motor, Bayless. I am building a sidevalve fitted with a Shorrock blower at the moment.
Cheers, David.
 
Ask about their Keystone line, if you want to save some money, they mix all of the paint from the same stuff, it's just their generic name.
 
I still need to finish my paint job. I have not used PPG but I know some who love it. This is the first car I have ever tried to put an expensive paint job on. I have been learning a lot and have bought from several different companies and have tried to find out all the info I can along the way. Most paint suppliers will be honest and tell you what you use with what. I would say that an all PPG setup will cost quite a bit. How many cars have you painted?
 
I've been using nothing but PPG for years, and love it. I'm comfortable using it, and that helps.
I shot my GT6 with the same materials that Bayless listed, and it turned out flawless.
I <u>do</u> have a separate primer gun for the high build primers, and that makes a difference. Dedicated gun for clear, too.
Jeff
 
I haven't used spray equipment in 30 years (used to spray custom lite fixtures using laquers and gold powder) and I think the basics are the same. I picked up a 10 piece HVLP kit from the PPG website (after making sure the local store can get parts) and plan to try the engine bay on the midget first and then go to work on the BGT later on. Here's the kit I got..
HVLP Kit

I'll stop at the store today and pick up some info on their products and the generics as Hap suggested.
 
Hi David. What sidevalve are you building? As long as the lower end can take it, I suspect a sidevalve is ideal for a blower.

Hate to hear the K200 is not available in CA but hope that doesn't apply to OK too. Is there a catalyzed replacement for it? Concept was already around the last time I bought some Deltron but I haven't used it yet. Does it handle similar to Deltron?

BTW, that HVLP kit looks like a good deal.
 
No problem with the bottom end, as I have had built "shell bearing" rods. I probably have near 4K in the motor and gearbox, if not more.
I have been using K36. it goes on ok, but is not as easy to sand as K200. The big difference in the Concept is that it goes off faster. Colour sanding and blending is far easier. I too use many different guns...also have one for spraying gel-coat.
Cheers, David.
 
Along with Dupont, PPG is one of the largest manufacturers of paint products, so they must be doing something right! I have used a few of their different lines and have had good results with all. Back in the day, their Ditzler line was the best for laquers and acrylics!!
 
Why do you have different guns for different paints? Are they the same brand/model gun with a different set-up or adjustment? Is a gun "contaminated" when switching from primer to clear coat? Or do different brands/types of spray equipment give their best with one particular type of paint. How do you find out which is best for each application without trying them all with each type of paint? I have done painting before but always used what was on hand rather than investing in my own. Now I have to spend my own money and want to get something good. Help!!!!
 
I have used Martin-Senour, DuPont, and PPG paints over the years. They all keep getting better.

When I painted the Mini I went with PPG's DCC product line. This is a two-component urethane but it's not a base/clear coat system. The retailer pointed out a trick they use which involves applying a third, final top coat that is thinned down 50% with PPG's DUU clear coat. The result is a very nice, smooth finish that can be wet sanded and buffed for high luster without worrying about removing the color. I found the paint fairly easy to apply and I'm happy with the results.
 
I'm into R&M Paint right now....Rinshed-Mason is the full name, I believe.
 
I have been using PPG paints and primers throughout the rebuild of my spitfire. Until doing this project I had NO experience with a paint gun. I have had very few issues with anything I have tried so far. A few runs here and there and some rough spots due to poor prep but those are my fault not the products. I am using their OMNI line of paints and it seems to cover well and is easy to use once you get used to it.

I's sure there are other products just as good. Most of the final result lies in proper preperation. Read that as many many hours of banging, filling, priming, sanding, cleaning, cleaning, and more cleaning. Did I mention that everything needs to be kept clean??
 
Back
Top