-
Hey Guest!
British Car Forum has been supporting enthusiasts for over 25 years by providing a great place to share our love for British cars. You can support our efforts by upgrading your membership for less than the dues of most car clubs. There are some perks with a member upgrade!**Upgrade Now**
(PS: Upgraded members don't see this banner, nor will you see the Google ads that appear on the site.)
Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
TR2/3/3A Distributor ground wire
- Thread starter RonR
- Start date
Share this page
TR3driver
Great Pumpkin - R.I.P
Offline
It should be riveted to the moving plate, the other end goes under one of the screws that anchors the fixed plate to the body. To replace it, you'll have to drill out the rivet and replace it with something. A copper pop-rivet should do nicely (but I've not tried it myself). A small bolt would probably work too, but be sure to stake the end so it can't come apart.
Geo Hahn
Yoda
Offline
Is a special wire needed for that to accommodate the flexing? Looks something like braided solder wick (only insulated).
On mine the end that is riveted seems to be soldered to little plate (and held under a bent tab) -- possibly a wire could be soldered at that connection w/o removing the rivet?
Really don't know, never had to replace that wire.
On mine the end that is riveted seems to be soldered to little plate (and held under a bent tab) -- possibly a wire could be soldered at that connection w/o removing the rivet?
Really don't know, never had to replace that wire.
TR3driver
Great Pumpkin - R.I.P
Offline
It should be a special extra-flexible wire, as any stiffness will impede the vacuum advance action. Ordinary stranded wire will also work harden and break quicker.
I don't know if the original Lucas wire could be soldered by ordinary means or not. But I tried to solder some similar wire for a phono arm once (a long time ago), and it was really tough to get even close to right. Each 'strand' is actually a very fine coil of wire wrapped around some sort of fiber. The whole mess would just fall apart when approached with a soldering iron.
I don't know if the original Lucas wire could be soldered by ordinary means or not. But I tried to solder some similar wire for a phono arm once (a long time ago), and it was really tough to get even close to right. Each 'strand' is actually a very fine coil of wire wrapped around some sort of fiber. The whole mess would just fall apart when approached with a soldering iron.
I have a new ground wire from Moss. It is a bare copper stranded wire with terminal ends at both ends.
The distributor, for whatever reason, is from a early 1960 Sprite (40919), not a TR3
The old ground wire is somewhat permanently attached, with the metal terminal end under the end of the pin in the contact breaker plate. The end of the pin has been spread out in a cross hatch pattern to secure the pin to the plate. It is not a rivit, but a 3/8-inch long pin with a groove near the end for the base contact breaker plate to ride in.
The question is how does one remove the old ground wire without damaging the pin?
Perhaps cutting the old wire off, leaving the terminal end under the pin, and then sodering the new wire to the old wire terminal end is the only solution. Or buy a new plate, if available.
The distributor, for whatever reason, is from a early 1960 Sprite (40919), not a TR3
The old ground wire is somewhat permanently attached, with the metal terminal end under the end of the pin in the contact breaker plate. The end of the pin has been spread out in a cross hatch pattern to secure the pin to the plate. It is not a rivit, but a 3/8-inch long pin with a groove near the end for the base contact breaker plate to ride in.
The question is how does one remove the old ground wire without damaging the pin?
Perhaps cutting the old wire off, leaving the terminal end under the pin, and then sodering the new wire to the old wire terminal end is the only solution. Or buy a new plate, if available.
JohnnyMead
Jedi Trainee
Offline
Advanced Distributors sells a 32 strand wire for this application. It's got lugs at both ends. See at:
https://advanceddistributors.mybisi.com/product/universal-distributor-groundearth-wire
when I got my distributor back from them it had the wire secured under the condenser screw. Probably not as secure as the staked pin, but it's worked fine.
john
https://advanceddistributors.mybisi.com/product/universal-distributor-groundearth-wire
when I got my distributor back from them it had the wire secured under the condenser screw. Probably not as secure as the staked pin, but it's worked fine.
john
JohnnyMead
Jedi Trainee
Offline
Correction: that advanced distributor wire is 350 strands. That's a lot of strands.