• Hi Guest!
    If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
    There are some perks with a member upgrade!
    **Upgrade Now**
    (PS: Subscribers don't see this gawd-aweful banner
Tips
Tips

Alignment question - cross tube locknut release?

Share this page

Re: Alignment question - cross tube locknut releas

skip&lynne,respectfully,i just saw the thing you guys fly over the river to your friends house,and you think im loopy? /ubbthreads/images/graemlins/crazyeyes.gif
 
Re: Alignment question - cross tube locknut releas

[ QUOTE ]
Who`s on first?

[/ QUOTE ]
Everyone at the same time. It amazes me how a simple "nutty" question can turn into a two page discussion.
D /ubbthreads/images/graemlins/grin.gif
 
Re: Alignment question - cross tube locknut releas

Lynne won`t get near the ultralight but she loves the red and white one it has doors and windows.
 
Re: Alignment question - cross tube locknut releas

dave russell,just wait,keoke will be back as well!and as far as i can tell lynne has not only the good looks,but the brains in that outfit!!!! /ubbthreads/images/graemlins/yesnod.gif
 
Re: Alignment question - cross tube locknut releas

[ QUOTE ]
The factory diagrams/Moss diagrams generally have RHD parts and assemblies illustrated. The LHD drive cars were considered a 'little export' project.

[/ QUOTE ]

Of course relying on any "authoritative" data blithely ignores the commonly DPO policy of doing it all exactly backwards or generally without regard to anything....
 
Re: Alignment question - cross tube locknut releas

[ QUOTE ]
dave russell,just wait,keoke will be back as well!and as far as i can tell lynne has not only the good looks,but the brains in that outfit!!!! /ubbthreads/images/graemlins/yesnod.gif

[/ QUOTE ]

Naw 7777, we gonna serve brains on sunday and you invited.---Keoke-- /ubbthreads/images/graemlins/yesnod.gif /ubbthreads/images/graemlins/laugh.gif
 
Re: Alignment question - cross tube locknut releas

keoke,ill be there early,gunna eat em all,lord knows i can use em!!!! /ubbthreads/images/graemlins/yesnod.gif /ubbthreads/images/graemlins/yesnod.gif /ubbthreads/images/graemlins/yesnod.gif
 
Just so happens that since I read this post I decided to check the BJ7 center rod and sure enough I too need to replace just one of the ends. Of course with it out of the car it's a little easier. I just put the rod in the vise and voila, it came right off. The PO replaced one side but not the other /ubbthreads/images/graemlins/frown.gif so now I have to try and locate a new RH thread end piece, anyone have one available????
Thanks for responding. /ubbthreads/images/graemlins/angel.gif
 
Nope Johnny, you plum out of luck---Keoke- /ubbthreads/images/graemlins/laugh.gif
 
Re: Alignment question - cross tube locknut releas

[ QUOTE ]
Just so happens that since I read this post I decided to check the BJ7 center rod and sure enough I too need to replace just one of the ends. /ubbthreads/images/graemlins/frown.gif so now I have to try and locate a new RH thread end piece, anyone have one available????
Thanks for responding. /ubbthreads/images/graemlins/angel.gif

[/ QUOTE ]
The rod ends are readily available as sets, but this would give you an extra. Maybe you will need it later?
D
 
Back
Top