Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Westfield_XI
Jedi Warrior
Offline
I am about to start my 11 project for the 1st time, but I have forgotten the firing order. I don't have my manual handy, can anyone help out?
-
Hi Guest!
If you appreciate British Car Forum and our 25 years of supporting British car enthusiasts with technical and anicdotal information, collected from our thousands of great members, please support us with a low-cost subscription. You can become a supporting member for less than the dues of most car clubs.
There are some perks with a member upgrade!**Upgrade Now**
(PS: Subscribers don't see this gawd-aweful banner
1275 firing order- help needed for 1st start!
- Thread starter Westfield_XI
- Start date
Share this page
OP
Westfield_XI
Jedi Warrior
Offline
Thanks, and under 10 minutes for a response!!
OP
Westfield_XI
Jedi Warrior
Offline
Not needed: I am running a MegaJolt system......
OP
Westfield_XI
Jedi Warrior
Offline
Oh, yes... it started right-up after about 1/2 a revolution of the crank in EDIS limp home mode. The carbs and their linkages are all out of wack and it didn't idle well, but it ran long enough to turn on the fan. I have an oil leak on the right side that I can't figure out though.
There is a threaded hole of about 3/8" diameter just behind the rearmost freeze plug and just under the oil fitting that goes to the remote filter that is leaking. Is this a vent or a port for oil temp or pressure? There is a port on the adaptor I installed where the oil filter used to be that I am using for oil pressure and I have a temp plug in the Speedwell oil pan. I left my manual in Tucson and I am in LA with the car.
I still have to wire up the gauges so I don't want to run it again until I do, that will be on Tuesday after the UPS delivery brings some parts.
There is a threaded hole of about 3/8" diameter just behind the rearmost freeze plug and just under the oil fitting that goes to the remote filter that is leaking. Is this a vent or a port for oil temp or pressure? There is a port on the adaptor I installed where the oil filter used to be that I am using for oil pressure and I have a temp plug in the Speedwell oil pan. I left my manual in Tucson and I am in LA with the car.
I still have to wire up the gauges so I don't want to run it again until I do, that will be on Tuesday after the UPS delivery brings some parts.
dklawson
Yoda
Offline
Westfield_XI said:
That position just about fully describes the point where an oil pressure gauge would normally connect to. I guess some filter heads may have pressure taps also, but the one you're describing is the standard one on the block. If you don't want to use it... it should be 1/8 BSP but I think you'll find a 1/8 NPT plug with some Teflon tape will seal it just fine.
Hap Waldrop
Yoda
Offline
Yep, sounds the stock pressure port, I'm guessing you must be picking up oil pressure up exterior of the engine, at the remote filter housing perhaps. It should have shot off like a cannon with oil if it were open.
I just got some parts for a fella who has just got a Westfiled 11 kit, cool cars.
I just got some parts for a fella who has just got a Westfiled 11 kit, cool cars.
OP
Westfield_XI
Jedi Warrior
Offline
Thanks, that's what I was hoping. I will get a plug tomorrow, my pressure signal comes from the filter adaptor, so I have no need of that one. I have all electric gauges and while it keeps fluids out of the cockpit it makes wiring the dashboard more complex. I am going to get the electrics completed in the next few days, close up the scuttle of the car and move on to tuning and adjusting everything to make it drivable.
Just a reminder of why I have been hanging about this forum for the past few years: my soon to be completed Westfield project contains much of a 1967 Sprite I bought for $300. In fact the engine block, crank, carbs, rear axle with brakes and front suspension uprights all came from the original donor. As well as the motor mounts, pedal box assembly with clutch and brake cylinders and two out of four wire wheel hubs. It had a nice fiberglass hardtop which I sold as well as the old rib case transmission, the windshield and some other parts. No one wanted the body (surface rust only) so I rented a small dumpster and cut it up with a sawzall in about an hour and a half. Anyway it still lives on as a bit racier of a car.
Just a reminder of why I have been hanging about this forum for the past few years: my soon to be completed Westfield project contains much of a 1967 Sprite I bought for $300. In fact the engine block, crank, carbs, rear axle with brakes and front suspension uprights all came from the original donor. As well as the motor mounts, pedal box assembly with clutch and brake cylinders and two out of four wire wheel hubs. It had a nice fiberglass hardtop which I sold as well as the old rib case transmission, the windshield and some other parts. No one wanted the body (surface rust only) so I rented a small dumpster and cut it up with a sawzall in about an hour and a half. Anyway it still lives on as a bit racier of a car.