Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
We are having an issue with our new brake system. We have excessive brake pedal travel with little rear braking. The front brakes seem to be working OK. We have noticed that when the pedal is depressed the the level of the fluid in the front chamber of the master cylinder rises with each depression of the pedal. We have rebuilt the brake master cylinder so assume that is OK. We have bled the system multiple times. Any thoughts what the problem might be?
-
The Roadster Factory Recovery Fund - Friends, as you may have heard, The Roadster Factory, a respected British Car Parts business in PA, suffered a total loss in a fire on Christmas Day. Read about it, discuss or ask questions >> HERE. The Triumph Register of America is sponsoring a fund raiser to help TRF get back on their feet. If you can help, vist >> their GoFundMe page.
-
Hey there Guest!
If you enjoy BCF and find our forum a useful resource, if you appreciate not having ads pop up all over the place and you want to ensure we can stay online - Please consider supporting with an "optional" low-cost annual subscription.**Upgrade Now**
(PS: Subscribers don't see this UGLY banner)
TR6 Brake problem
- Thread starter ceedub
- Start date
Share this page
trrdster2000
Luke Skywalker
Offline
ceedub, adjust the rears until they are locked, then see what you have. That gives a start on what it isn't. The master repair can sometimes go wrong, have you been doing this before???
Wayne
Wayne
Hi Wayne,
We did lock up the rears with no luck. We are thinking that the MC may have been bored out and thus the new secondary piston seal is not working as it should. Instead of fluid being pushed out to the back it is being pushed back into the front of the MC. We have not done a MC repair before but were pretty careful how the seals were installed.
We did lock up the rears with no luck. We are thinking that the MC may have been bored out and thus the new secondary piston seal is not working as it should. Instead of fluid being pushed out to the back it is being pushed back into the front of the MC. We have not done a MC repair before but were pretty careful how the seals were installed.
trrdster2000
Luke Skywalker
Offline
Ceedub, You do have a M/C problem. The seal at the rear is the one that holds fluid in the rear brake chamber. If you did hone it out too far it will by pass the cup and go into the front chamber. Sorry to say you will need another one to repair or get a new one.
Wayne
Wayne
We did not hone the MC but upon taking it apart and more careful inspection we could see that the deepest part of the bore was a little chewed up as if someone had tried to hone it and was not too successful. So, I bit the bullet and bought a new MC so when I get a little time I will replace it and bleed the system yet again, hoping that we will have some braking. Sure glad I used dot 5 or there would not be much left of my engine compartment paint.
trrdster2000
Luke Skywalker
Offline
ceedub, Dot 5 can start World War lll here, but I agree with you. I did the master on the '37 MG in the '80's and it sat until 2012, I did pump it once in a great while. We gave it a couple of pumps when we moved and it blew the rear flex hose. Good stuff.
Wayne
Wayne
Similar threads
Similar threads
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
TR2/3/3A Aftermarket brake and clutch master cylinders - black extension?- Started by 71TR6
- Replies: 6
-
-
A friendly reminder - be careful what links you click on here. If a link is posted by someone you don't know, or the URL looks fishy, DON'T CLICK. Spammers sometimes post links that lead to sites that can infect your computer, so be mindful what you click.