Hey - did you know if you click on the title of a thread it will take you to the first unread post since you last visited that thread?
but were afraid to ask: 
STOP!! Never post your email address in open forums. Bots can "harvest" your email! If you must share your email use a Private Message or use the 
smilie in place of the real @
Pretty Please - add it to our Events forum(s) and add to the calendar! >> 
Hi guys. The rubber seals that fit over the wiper wheebox spindles on my BJ8 have perished and allow water to run down the shaft and drip inside my car so they need replacing. I haven't found any parts supplier that sells these but I have read on the MGA site of someone dismantling the wheel box to remove the shaft to replace it - I don't want to risk that but wondered if anyone else had obtained any rubber seals and just stretched them over the splined head onto the shaft, or achieved a seal some other way? BTW I'm not referring to the flat rubber gasket that fits on the shroud. Richard in UK
-
The Roadster Factory Recovery Fund - Friends, as you may have heard, The Roadster Factory, a respected British Car Parts business in PA, suffered a total loss in a fire on Christmas Day. Read about it, discuss or ask questions >> HERE. The Triumph Register of America is sponsoring a fund raiser to help TRF get back on their feet. If you can help, vist >> their GoFundMe page.
-
Hey there Guest!
If you enjoy BCF and find our forum a useful resource, if you appreciate not having ads pop up all over the place and you want to ensure we can stay online - Please consider supporting with an "optional" low-cost annual subscription.**Upgrade Now**
(PS: Subscribers don't see this UGLY banner)
Windscreen wiper wheelbox rubber shaft seal
- Thread starter Tricky
- Start date
Share this page
Hi Steve, thanks for the reply. That is indeed the part in question but strangely it isn't available separately despite being an item that deteriorates over time and crucial to the fight against water ingress! I suspect that I'm going to have to find some suitably thicker rubber or silicone sheet that I can punch a hole in and slide over the splined end - I really don't want to risk dismantling the shaft and risking damaging it, then having to replace both wheel boxes. Somebody else must have replaced these rubbers at some point - I can't believe that I'm the first!
Offline
This UK supplier has all kinds of great stuff.
https://simplybearings.co.uk/shop/
These v-rings look good:
Idea: if they won't stretch over the splines, you could cut with a razor and hold around the shaft with zip tie or wire.
Edit: body copy says they are stretchable.
Please let the Forum know your solution.
https://simplybearings.co.uk/shop/
These v-rings look good:
Idea: if they won't stretch over the splines, you could cut with a razor and hold around the shaft with zip tie or wire.
Edit: body copy says they are stretchable.
Please let the Forum know your solution.
Last edited:
Offline
O ring that stretches . If you must cut it,
use a diagonal cut so ther is overlap. There is o ring adhesive ( like crazy or super glue ). Heat shrink tubing is also great to work with - large sizes available.
Bob
use a diagonal cut so ther is overlap. There is o ring adhesive ( like crazy or super glue ). Heat shrink tubing is also great to work with - large sizes available.
Bob
Similar threads
Similar threads
-
-
-
-
-
-
-
-
-
-
M
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
A friendly reminder - be careful what links you click on here. If a link is posted by someone you don't know, or the URL looks fishy, DON'T CLICK. Spammers sometimes post links that lead to sites that can infect your computer, so be mindful what you click.