Search:

Type: Posts; User: Jayplum; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    Thanks
  2. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    Thanks. Haven’t seen an expander in years

    will check.
  3. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    Moss indicated the same as we all thought. One hub for all.
    only conclusion is that PO installed hubs from another vehicle which has compatible bearings and lug pattern.
    I am going to rehab spare...
  4. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    Yeah, already did the rear studs; quite the job. Used blue Locktight which did not set up; should have used red.
    Waiting to see if Moss has a solution to the grease cap.
  5. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    I have had excellent responses and assistance from TRF and Moss over the years. No reflection on either.
    As to that, I believe the current problem is the loose nut behind the (steering) wheel -...
  6. Replies
    28
    Views
    887

    TR6 Re: High Compression in One Cylinder

    Could just be that the #1 is carboned up due to running cooler as a normal condition than the other cylinders. All the fixes mentioned are good. Used to find a 'top end' oil to clean out old V8's;...
  7. Thread: TR3 Hard top

    by Jayplum
    Replies
    5
    Views
    568

    For Sale Re: TR3 Hard top

    Sorry, thought I had already responded to you. I may have not saved/posted. Older I get the dumber I feel.
    Anyway, have a bid and accepted offer on the top; waiting for buyer to get back from...
  8. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    tried several items to secure to include a cold chisel, block of wood, several mallets and hammers, etc.
    problem appears to be the lip is curled under which will not push out the band to tighten...
  9. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    nothing like a sudden rattle at 60 plus to get your attention
  10. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    bought two from TRF. Both the same. Just ordered two from Moss; will check them out.
    in dealing with AM parts it can be hit or miss. Don’t blame TRF just a miss
  11. Replies
    21
    Views
    1,030

    TR2/3/3A Re: Side screen location.

    TRF is totally in control.
  12. Replies
    21
    Views
    1,030

    TR2/3/3A Re: Side screen location.

    Mine left last week going to TRF. Sent mine as is; fitted but not media blasted.
  13. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    Severly
  14. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Re: Grease cap

    Thanks. Cap is new and is a loose fit that will not stay.
  15. Thread: Grease cap

    by Jayplum
    Replies
    25
    Views
    926

    TR2/3/3A Grease cap

    This may be a dumb question but is there a trick to securing the grease cap on a TR3 rotor.
    There is a hole in the center, assuming for a grease fitting but the cap is not designed to be secured....
  16. Replies
    21
    Views
    1,030

    TR2/3/3A Re: Side screen location.

    Appreciate this thread. I have this ahead of me and have gained a lot from y’all’s discussion.
    thanks Charlie and David
  17. Replies
    21
    Views
    1,030

    TR2/3/3A Re: Side screen location.

    I had a similar alignment and found I had put the brackets in the wrong places (#2 was in #4 spot, etc)once corrected they were parallel again. mine are wedge type but the principle should be the...
  18. Replies
    5
    Views
    255

    TR2/3/3A Re: Front suspension / springs

    Thanks to all. Appreciate the input.
  19. Replies
    5
    Views
    255

    TR2/3/3A Re: Front suspension / springs

    Yeah, my kidneys are very familiar with the ride. Seems to me that the longer spring with no spacer would give the better ride and possibly more 'travel' in the front suspension. I don't want to...
  20. Replies
    5
    Views
    255

    TR2/3/3A Front suspension / springs

    I am currently rebuilding the front suspension on my 57 TR3. Question came up on front springs. Seems there are several configurations applicable; with or without alloy spacer / original spring...
  21. Thread: TR3 Hard top

    by Jayplum
    Replies
    5
    Views
    568

    For Sale Re: TR3 Hard top

    If you have any interest we can work out something to help with delivery; meet half way, etc.
  22. Thread: Quiet

    by Jayplum
    Replies
    12
    Views
    629

    TR2/3/3A Re: Quiet

    looks great
  23. Thread: Quiet

    by Jayplum
    Replies
    12
    Views
    629

    TR2/3/3A Re: Quiet

    Good idea.
  24. Thread: Quiet

    by Jayplum
    Replies
    12
    Views
    629

    TR2/3/3A Re: Quiet

    Tried that but could still feel the heat!
  25. Thread: Quiet

    by Jayplum
    Replies
    12
    Views
    629

    TR2/3/3A Re: Quiet

    Thanks
Results 1 to 25 of 74
Page 1 of 3 1 2 3