Search:

Type: Posts; User: carpecursusII; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    853

    TR2/3/3A Re: Speedometer Routing

    Ill throw a different opinion out there. Here are two Tr2s, no OD, that have a different routing. The red car is TS 5265 found in very original condition and the white car is TS3285 also in...
  2. Replies
    12
    Views
    1,198

    TR6 Re: Why were all these shims in there?

    The shim packs will help set the distance from hub center to hub center as the frames could vary by a certain amount.
  3. TR2/3/3A Re: What is the name of this bracket and is it still avaiable?

    I've got a few on the shelf in good condition. PM me.
  4. TR2/3/3A Re: 'A' type Front calipers, TR3 vendor???

    I think I have a whole rebuilt caliper on my shelf. Which side do you need?
  5. Wanted triumph spitfire mk2-3 drivers seat bucket

    I need a driver side bucket for a mk2/3 spitfire. I don't need the seat rails but I can take them.
  6. Replies
    6
    Views
    729

    General TR Re: Has anyone used these poly bushings

    Don't use the cheaper poly offered by moss for the front upper A-arms, they are improperly designed and will not hold the suspension in the correct position.
  7. Replies
    61
    Views
    5,041

    TR2/3/3A Re: Water Pump "Here I Go Again"

    I can attest to the skill of the dutchman, he's done a few pumps for me and in about a week. He even offered to fix a Moss pump that was sent to me with the impeller installed wrong. I would not...
  8. Replies
    14
    Views
    2,214

    TR2/3/3A Re: TR3 engine hand crank

    Black
  9. Replies
    26
    Views
    3,951

    TR2/3/3A Re: Carburetor Rebuild

    I think there may be some confusion here regarding timing. Triumph called for 4 degrees BTDC static, Jeff at AD calls for anywhere from 10-14 BTDC AT IDLE* with the vacuum disconnected. It's two...
  10. Replies
    3
    Views
    965

    TR2/3/3A Re: install the OD relay

    connectors point down.
  11. Replies
    1
    Views
    504

    TR2/3/3A A-type overdrive drain plug oring

    Some time ago someone here posted the o-ring specs to replace the fiber washer on the drain plug with a rubber oring. Can anyone remember what it was??
  12. Replies
    1
    Views
    938

    Wanted Re: TR3 Original Tail light lens

    I sent you a PM
  13. Replies
    8
    Views
    1,145

    TR4/4A Re: Well...another stripped trunnion

    I had this problem recently with my 3. I think the new washers they provide are not soft enough to absorb the splines. The splines are also bigger on the new trunnions. I drilled out the washers a...
  14. Wanted Re: Heater Core, Capping Trim, OD switch 1959 TR3

    PM sent.
  15. Replies
    574
    Views
    139,247

    TR2/3/3A Re: Beginning the TR2 Bodywork

    JP, are you a rower?
  16. Replies
    1
    Views
    1,145

    Wanted Re: TR6 rear trailing arms

    I've got a driver side. $50+shipping.
  17. Replies
    11
    Views
    1,609

    TR6 Re: Front sealing block

    Forget the helicoil business, I just helped a friend install the new steel block linked above and it is the correct solution. We had to remove the old block because it had been helicoiled and didn't...
  18. TR2/3/3A Re: Replacement Floor and Trunk Panel Quality

    I have purchased all the pieces, the best fit is as follows. Inner sills from TRF, floors from Moss or Rimmer, trunk floor (pre 60k) from TRF or VB. VB was actually stocking parts from TRF, at the...
  19. Replies
    37
    Views
    4,449

    TR2/3/3A Re: Fabricating inner sills?

    What ever you do don't buy the British heritage inner sills, they are not properly formed. Purchase from TRF.
  20. Replies
    9
    Views
    1,499

    TR2/3/3A Re: Grease Gun Color

    Oh, the cap of the gun (to retain the grease) is bare metal. The end cap over the nozzle, I'm not sure, possibly black like the rest of the gun.
  21. Replies
    9
    Views
    1,499

    TR2/3/3A Re: Grease Gun Color

    bare metal with the words stamped in it.
  22. Replies
    9
    Views
    1,499

    TR2/3/3A Re: Grease Gun Color

    John, you should have the Enots #1 D grease gun. this is it but it is missing its cap.
    ...
  23. Replies
    6
    Views
    1,009

    TR2/3/3A Re: Lockheed diff setup

    A good rear end shop can fix that problem. Take it in and ask them. You can fix the pattern with shims under the bearings.
  24. Replies
    574
    Views
    139,247

    TR2/3/3A Re: Beginning the TR2 Bodywork

    David, TRF is over priced, if your spending that money just buy Skinner. Moss is good for carpet as they stock it and the price is good. Skinner can put together a whole kit and do it properly. If...
  25. Replies
    574
    Views
    139,247

    TR2/3/3A Re: Beginning the TR2 Bodywork

    I noticed many parts of that eBay car that are not tr2, and the parts that are missing are not easy to find!
Results 1 to 25 of 210
Page 1 of 9 1 2 3 4