Search:

Type: Posts; User: TRclassic3; Keyword(s):

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. TR4/4A Re: Help with deciphering front suspension problem

    Quick update. Just studied the movement some more. It doesn’t appear that the trunion pins have play within the bushing but that the trunion is simply rotating a bit and that movement transfers all...
  2. TR4/4A Re: Help with deciphering front suspension problem

    thanks for the response. the jack was placed on the frame about a foot behind the wheel
  3. TR4/4A Re: Help with deciphering front suspension problem

    thanks for the response. Close visual inspection does not show anything missing or broken. When I force the movement there is no independent movement between the trunion and the VL, the VL and the...
  4. TR4/4A Re: Help with deciphering front suspension problem

    Thanks for the response. I wondered as well if the bang was spring relocating. Visual inspection did not show any signs of movement, not that that proves anything. I am beginning to think the bang...
  5. TR4/4A Help with deciphering front suspension problem

    I had an "interesting" problem develop with front suspension on early TR4. The issue started when I began jacking the right side of the car. Just as the tire was lifting off the ground (thus weight...
  6. TR4/4A A type OD working in 3rd but not in 4th

    This seems like a bit of an odd problem. A little history: After OD and transmission rebuilt an installed, a test drive gave sporadic results. Initially seemed fine but began dropping out of OD or...
  7. Replies
    5
    Views
    585

    TR2/3/3A Re: Front wheel bearing adjustment

    Interesting the the end float measurement is taken without the felt seal in place. I would assume then that once the seal is added no end float would be detectable....or at least no rock in the...
  8. Replies
    5
    Views
    585

    TR2/3/3A Front wheel bearing adjustment

    After refreshing my memory on wheel bearing adjustment by searching and reading some of the existing posts, I find I am left with a question I haven't found the answer for. Following the updated...
  9. Replies
    5
    Views
    776

    TR2/3/3A Re: SU Upper jet bearing position

    Charley hit the nail on the head...some how had managed to get an extra washer on top of the upper bearing. Removed and reinstalled and things seem good...AND NO LEAK.
  10. Replies
    5
    Views
    776

    TR2/3/3A Re: SU Upper jet bearing position

    Thanks for the feedback. I do still have the old bearing and can compare. Interesting thought about an extra washer...if that exists it would have to be stuck up in there. The jet will come up to...
  11. Replies
    5
    Views
    776

    TR2/3/3A SU Upper jet bearing position

    I've been fighting an annoying leak on the front carb. Made multiple attempts to remedy using the existing cork re-soaked in oil, new cork soaked in oil, "leak proof" O rings. I think I have...
  12. Replies
    6
    Views
    850

    TR2/3/3A Re: Help with fuel gauge blowing fuse

    Thanks Doug. The plot thickens a bit. This morning I hooked up a ground (gauge still out of dash) turned the key and the gauge went to full (which it is) and no problem with the fuse blowing I put...
  13. Replies
    6
    Views
    850

    TR2/3/3A Re: Help with fuel gauge blowing fuse

    Thanks Randall. I think that my initial conclusion that the heater circuit was the problem was in error. I had popped the gauge out of the dash, removed the heater wire and the fuse didn't blow. ...
  14. Replies
    6
    Views
    850

    TR2/3/3A Help with fuel gauge blowing fuse

    A little background....while engine out for rebuild I put in a new wire harness. Everything had been fine, but while out for a ride yesterday I blew a fuse. I was able to eliminate the wiper, brake...
  15. Replies
    6
    Views
    1,201

    TR2/3/3A Extreme tire wear

    Need some suggestions here. Experience rather extreme tire wear on the inside of the right side front tire. What's the most likely cause? Alignment? Something bent causing camber issue? I had...
  16. Replies
    2
    Views
    893

    TR2/3/3A Re: TR3 Monza Exhaust installation

    Thanks M. Pied. Seems someone out there would have installed one of these.
  17. Replies
    2
    Views
    893

    TR2/3/3A TR3 Monza Exhaust installation

    I have one of these systems on the way. Any tips or tricks, or horror stories about installation? Looks like from the picture that the original rear hanger is not used. I that correct? Is a new...
  18. Replies
    43
    Views
    7,160

    Re: TRA at Kentucky Lake - June

    Mickey

    Wouldn't miss it. It's always a great time with wonderful friends, and fantastic cars. In answer to the question about the number of cars, it is generally between 50 and 70 side screens...
  19. Replies
    5
    Views
    1,674

    TR6 TR6 twist from John Twist

    I was surfing through Youtube the other day and was watching a few of the Unversity Motors videos. In this particular one, Mr Twist was working on a TR6, and a couple of comments caught my interest....
  20. Replies
    9
    Views
    1,079

    Re: Side curtain window

    Thanks to all for the responses. I had looked for them on TRF and only found a listing refencing the wedge type. Took another look and found them listed. Not sure what I missed the first time.
    ...
  21. Replies
    9
    Views
    1,079

    Side curtain window

    Can anyone suggest a source for the stationary side curtain window. dzus type
  22. Replies
    15
    Views
    8,143

    Re: any one got a spare 9 grand

    Amen to that!
  23. Replies
    15
    Views
    8,143

    Re: any one got a spare 9 grand

    Trade you for the Porsche, Ralph.
  24. Replies
    15
    Views
    8,143

    Re: any one got a spare 9 grand

    Sad but true.
  25. Replies
    2
    Views
    4,516

    Re: Brake booster

    Interesting and very plausible explanation as this car was at the very end of the 2500M run. Thanks for the response.
Results 1 to 25 of 254
Page 1 of 11 1 2 3 4