Search:

Type: Posts; User: TuffTR250; Keyword(s):

Page 1 of 27 1 2 3 4

Search: Search took 0.01 seconds.

  1. TR2/3/3A Re: Question on torquing nut on steering box rocker shaft

    Thanks for the responses!! I will try tightening the top cover adjustment screw just a bit more and see how that works.
    Bob
  2. TR2/3/3A Re: Question on torquing nut on steering box rocker shaft

    My steering box is still out of the car, but fully assembled. Today I adjusted the screw on the top of the steering box for when the Rocker shaft was in the middle, it took 1/4 turn of the screw to...
  3. TR2/3/3A Re: Question on torquing nut on steering box rocker shaft

    Thanks John!
    Bob
  4. TR2/3/3A Question on torquing nut on steering box rocker shaft

    When torquing the large nut on the steering box rocker shaft (Macy's says 80 lbs) is it necessary, or possible, to somehow hold the rocker shaft so pressure is not put on the arm of the rocker shaft,...
  5. TR2/3/3A Re: Is it possible to buy stronger springs for turn signal lever in control head?

    I finally did get it working correctly. Mine only had washers at the top of the springs. I added some at the bottom as well. Thanks!
    Bob
  6. Replies
    2
    Views
    231

    TR2/3/3A Re: Question on steering idler unit

    Thanks Randall!
    Bob
  7. Replies
    2
    Views
    231

    TR2/3/3A Question on steering idler unit

    On the steering idler unit (under the section: TO FIT IDLER UNIT) the manual says to screw the fulcrum pin into the housing and unscrewing one full turn; ensure also that the grease seal is in good...
  8. Replies
    27
    Views
    768

    TR2/3/3A Re: Speed O not working

    Thanks for this forum thread!! I learned a lot from it.
    Bob
  9. TR2/3/3A Re: Is there a Delrin bush available for the top of TR3 steering column instead of fe

    My son and I got the Rimmer top bush installed in my TR3. We drilled holes for the rubber nipples to hold to the steering column so the bush would not turn in the column. We put it in flush with the...
  10. TR2/3/3A Re: Is it possible to buy stronger springs for turn signal lever in control head?

    Thanks for the responses! Sounds like it is not a good idea to change the lever springs.
    Bob
  11. TR2/3/3A Is it possible to buy stronger springs for turn signal lever in control head?

    I have taken apart my steering wheel control head and replaced a couple of parts and greased with Dry Moly and white lithium grease. The turn signal lever moves real well on and off but will not self...
  12. TR2/3/3A Re: Is there a Delrin bush available for the top of TR3 steering column instead of fe

    Roy (TR-3rg), I finally got the Delrin upper steering column bush p/n RTR3492 from Revington. I have a question about installation. Does it get installed flush with the top of the outer steering...
  13. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Thanks Randall. I agree that the light spring does look like the one that goes under the contact. Now that I've messed with it some more I think the light spring is too weak to work correctly with...
  14. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Sorry for the long Thread. I'm still fiddling with my control head. I got a few parts from a club member. Wondering which of these in the picture would be the best for the turn signal lever arm? I'm...
  15. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Thanks for the information John. My control head seemed to clean up pretty good since I took it totally apart. At this time everything appears to be ok except the turn signal cancel. I believe that a...
  16. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Mine cancelled sporadically but mostly I had to turn off the turn signals manually. I have attached another picture of mine showing what holds it at 6:00 o'clock.
    Bob

    61875

    And here is...
  17. TR2/3/3A Re: Questions on TR3A steering control head refresh

    I see that the cancelling ring pictured above by Frank appears to be quite different from mine. Does anyone know if the cancelling rings are interchangeable between what appears to be design changes...
  18. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Thanks Frank! I don't know if that one would work or not. I notice your ring is not solid all the way around, and it has a different shape for holding the vertical lever of the solar tube. I'll keep...
  19. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Thanks Randall! I will try some of that Dry Moly since the front part turns quite a bit harder than it seems like it should.

    On the repair of the ring, I was skeptical of JB Weld and your...
  20. TR2/3/3A Re: Questions on TR3A steering control head refresh

    A question concerning the turn signal cancelling ring. As can be seen in the attached pictures, on mine there is quite a divot where the cam pieces go across the raised area in the cancelling section...
  21. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Randall, that raises a question.. The back portion of my stator tube bracket (the larger diameter piece) that has the "vertical lever of the stator tube" does not turn very easily over the front part...
  22. TR2/3/3A Re: Questions on TR3A steering control head refresh

    A question...If I have the flasher control lever positioned at 12 o'clock, and the vertical lever of the stator tube at 6 o'clock, and the slot in the stator tube slide into the indentations on the...
  23. TR2/3/3A Re: Questions on TR3A steering control head refresh

    I had an idea! I pushed the trunion down into the hole and using a screw driver I pushed the roller into it's central position. That held the turnion in. I then removed one of the springs from the...
  24. TR2/3/3A Re: Questions on TR3A steering control head refresh

    Thanks a lot Randall!!! Your pictures really help!!! I was trying to follow the instructions from Ian Cornish but I was struggling with understanding how it would go together with his steps. From...
  25. TR2/3/3A Re: Questions on TR3A steering control head refresh

    I'm now preparing to reassemble the control head. All the articles I've seen posted only provide step by step procedures for disassembly but no reassembly. Are there any good detailed step by step...
Results 1 to 25 of 659
Page 1 of 27 1 2 3 4