Search:

Type: Posts; User: wangdango; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    91

    BJ8 heater blower?

    My blower is cracked and I would just prefer to buy a used one, restore it, and change it over for the cracked one. Question is, can I take it out without removing the fender?
  2. Replies
    3
    Views
    164

    BN2 wheel cylinders/rebuild/replace?

    Our '56 BN2 vintage race car has been on the shelf since my 1st child, (and now includes my 2nd child), so 10 yrs have gone by, the engine is all redone and I just need now to spend the time and go...
  3. Replies
    17
    Views
    589

    Re: Head gasket question

    The thing to remember is that the AH 100/4 head stud spacing is what causes the leaking. You can have a brand new head, and a 'decked" block, and it will still leak. DW will tell you NOT to coat...
  4. Replies
    17
    Views
    589

    Re: Head gasket question

    I would suggest emailing DW about re torquing the head, pretty sure they say not to do that!
  5. Replies
    17
    Views
    589

    Re: Head gasket question

    Michael-
    We also have the DW steel gasket but not an alloy head (VSCCA does not allow it, but plenty of people are running them). They can be used as stated 3 times. We have never coated them with...
  6. '67 XKE Mallory dulal point to Pertronix

    I would like to replace my dual point with a Pertronix distributer, how hard is this to switch over?
  7. Replies
    22
    Views
    979

    Re: Choke sticking

    I have not tried it yet, but Norman Nock has some springs which are added between the cable and the lever arms, (I am just going to use a hardware spring of appropriate size). Check out their...
  8. Replies
    34
    Views
    2,346

    Re: BJ8 wiring diagram in ladder logic

    Bill
    Excellent work, can you email me a PDF as well? (epreusser@gmail.com)
  9. Replies
    4
    Views
    454

    BJ8 inner battery hold down?

    I am just finishing up installing a trunk liner kit on my BJ8 and trying to make it as correct as possible. I do not see how the inner battery hold down bar is attached to secure the battery in the...
  10. Replies
    6
    Views
    420

    Re: BJ8 console redo?

    Thanks, I will attempt to do it myself, anyone making repops of the chrome console trim (the long strips on each side)?
  11. Replies
    6
    Views
    420

    BJ8 console redo?

    I would like to send my console out to be redone/restored, anyone have a good source to do this?
  12. Replies
    8
    Views
    588

    Re: Broken Spokes

    While S/S spokes look great they do stretch and will do that only so many times until they break. The regular steel ones are slightly better in they are less brittle. We have vintage raced our 100...
  13. Replies
    2
    Views
    343

    BJ8 door hinge milling?

    The right hand door is tight on closing side and so much so it touches ever so much with the rear fender. The prior owner welded in new hinge pillars and the front and rear fenders line up...
  14. Replies
    1
    Views
    359

    BN2 wheel cyclinders/replacement

    Our 100 has been sitting idle for about 8 years and the brakes are going to need a going over, rather then go to the trouble rebuilding them, does one of the usual suppliers have QUALITY...
  15. Replies
    4
    Views
    666

    Birds of a feather......

    Just came across this picture from a number of years ago of our 100 LeMans, and a "matching" 100M.
    52871
  16. Replies
    1
    Views
    521

    BJ8 seat restoraton?

    I would like to redo the vinyl front seats on my BJ8, I have a set of nos foam for the bases and the backs. Have heard the foam we get now is way too firm compared to what is/was originally done. ...
  17. Replies
    2
    Views
    798

    '67 XKE rear diff?

    I changed the rear diff oil today and had both rear wheels up on jack stands. While it was up I rotated the rear wheels to check for brake drag, and while there was none, there was some resistance...
  18. Replies
    7
    Views
    961

    BJ8 foot well vinyl panels?

    I am replacing the foot well vinyl panels on my BJ8, prior owner had redone them wrapped in carpet. How are they attached,(from the factory), the passenger panel is two pieces, why is that? This is...
  19. Replies
    11
    Views
    1,791

    Re: Home-made ducting for BJ8 radiator?

    Jerry,
    I am open to all. Realize the original design is ok, but not great, I would like to get more air flowing thru the grill and into the radiator.
  20. Replies
    2
    Views
    498

    BJ8 lower radiator hose!

    Was replacing the hoses on my BJ8 and the lower one is a bear to get on and have the hose clamp fitted. So, I put the clamp on the end of the hose,and put black electric tape behind it to prevent it...
  21. Replies
    11
    Views
    1,791

    Home-made ducting for BJ8 radiator?

    I know several of you have made additional sheet metal ducting to keep the air into the radiator, question is did anyone do it and have templates of the pieces they fabricated? I would like to do...
  22. Replies
    53
    Views
    5,334

    6-cylinder alloy valve cover

    I am considering upgrading, anyone have opinions etc?
  23. Replies
    26
    Views
    2,909

    Re: Stripped Thread in Gas Tank

    If you want 1st class hardware and a big variety of it, try McMaster Carr, do not have the website but you can google them. They have virtually any fastener anyone could ever want, which includes...
  24. Replies
    4
    Views
    582

    3000 valve cover bolts/chrome/ss?

    Was wondering if anyone had a vendor source for either chrome or stainless nuts/washers to hold down the 6 cycl valve cover
  25. Replies
    3
    Views
    540

    BJ8 valve adjustment?

    I presently getting my BJ8 back on the road and noticed the prior owner restamped the valve cover adjust valves to "HOT" rather then the stock decal saying "COLD." Question is how bad will this mess...
Results 1 to 25 of 196
Page 1 of 8 1 2 3 4