Search:

Type: Posts; User: John Turney; Keyword(s):

Page 1 of 145 1 2 3 4

Search: Search took 0.05 seconds.

  1. Re: I'm Sick of Seeing People Wearing Masks!

    Tabasco sauce mixed into your hand sanitizer works too.
  2. Replies
    4
    Views
    79

    Re: Over 100 thousand

    Especially since they are asking medical & nursing students to help out.
  3. Replies
    1
    Views
    39

    Re: A duck walks into a shop

    LOL
  4. Re: Rear shroud connection to the floor pan on a BJ7

    :iagree:
  5. Re: BJ8 Phase 1 left turn signal (driver side)

    Sounds like a wire to the front left is disconnected. That makes the rear flash quickly to let you know the front bulb is burned out. Since you changed the bulb, the next thing to check is a break...
  6. Replies
    10
    Views
    246

    Re: BJ7 HS6 Carb Baseline Setting

    I had that at one time. A small piece of debris was holding a throttle plate open.
  7. Replies
    12
    Views
    1,024

    Re: side change gear box stuck in top gear

    Same situation here.
  8. Replies
    8
    Views
    193

    Re: BJ8 Frame Rust Options?

    If anyone makes that frame section, it would be Kilmartin, http://www.kas-kilmartin.com.au/Austin%20Healey.htm.

    What gives me pause is that other frame parts are more known for rust-through. If...
  9. Re: BN6: Shock absorbers do not fit after renewing the link arms

    Volker,

    There should be a distance tube, Moss#725-130, between the two ears on the axle. The upper stud goes through it. Tightening the nut while holding the hex section on the stud should pull...
  10. Replies
    7
    Views
    153

    Re: 8 months today

    Cute!
  11. Replies
    4
    Views
    140

    Re: Day 11 - Cabin Fever

    LOL!!!
  12. Replies
    12
    Views
    235

    Re: Son called to duty

    Good luck to him.
  13. Replies
    19
    Views
    433

    Re: Fuel prices

    Saw regular for $2.99 Friday at the corner 7-11. That's low for us.
  14. Replies
    13
    Views
    506

    Re: Too many tools?

    I've found that the best way to find that tool you've been looking for is to buy another one. Then the lost tool magically shows up.
  15. Re: 6 Blade cooling fan for 64 BJ8, advice?

    I have one of the original Texas Coolers. I have also put a partial shroud around it.
  16. Re: Healey assembly line - engine installation

    The body number is stamped on one of the hood hinges, and the hood latch as well as the batch/body plate so they can reunite the correct hood with the body.
  17. Replies
    60
    Views
    1,640

    Re: Steering not right

    When I tackled my steering box years ago, the bearings were bad. The inner race on the worm was pitted and I had a machine shop cut it down and reshape it since new worms were not readily available....
  18. Re: If You Get an email That Says "Knock Knock"

    :highly_amused:
  19. Replies
    7
    Views
    281

    Re: fan belt change on BJ8

    Getting the old belt off is easy - just cut it. Getting a new one on is the hard part.
  20. Re: Healey assembly line - engine installation

    My guess is that it moves crane attachment point front and back to tilt the engine. The wheel probably rotates a screw inside the beam. Mine does that, except I have a crank instead of a wheel.
  21. Re: Things to Do While You are Sheltering in Place

    :iagree:
  22. Replies
    11
    Views
    380

    Re: Gearbox Identification

    MOWOG 1H3150 from the first photo.
  23. Replies
    11
    Views
    380

    Re: Gearbox Identification

    A Google search leads to a MGA: https://mgaguru.com/mgtech/gearbox/gt101.htm
  24. Re: Things to Do While You are Sheltering in Place

    I saw Fangio doing a demonstration drive in the W196 at the Monterey Historics, before it became the Rolex Reunion. There was a 500SL camera car leading him. We could tell he was annoyed that the...
  25. Replies
    32
    Views
    1,414

    Re: Healey ergonomics question

    I'm 6' and fit just fine. It's a bit "ungainly" getting in and out, especially with the sidecurtains in place. I've made a couple of tweaks to raise the front edge of the seat about 1/4" for better...
Results 1 to 25 of 3615
Page 1 of 145 1 2 3 4