Search:

Type: Posts; User: CJD; Keyword(s):

Page 1 of 216 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    17
    Views
    547

    TR2/3/3A Re: OD cover plate gasket sealer.

    And I don't think the box lasted long. Mine, car 5248, did not have the box, so it had disappeared by 1954.
  2. Replies
    12
    Views
    428

    TR6 Re: Why were all these shims in there?

    Good effort in getting close...but still save the shims as you should reset alignment after full running gear is in place and suspension has settled into a permanent set.

    I made the mistake of...
  3. Replies
    12
    Views
    428

    TR6 Re: Why were all these shims in there?

    I agree, suspension geometry must be adjusted with weight on wheels and all settled into its normal ride height. Jag was an exception, where you used special spacers to set a "standard" height. I...
  4. Replies
    5
    Views
    242

    TR2/3/3A Re: Side screen location.

    Great...if you already have the window acetate you can use that to make sure the angles on the frame are correct. The window plastic will dictate the final angle of the front rail of the frame.
    ...
  5. Replies
    2
    Views
    187

    General TR Re: Fuel filter before the pump.

    Yep. I have a brand new tank, yet still get rust particles in the filter.
  6. TR2/3/3A Re: Question on torquing nut on steering box rocker shaft

    +1. Adjust the bolt so you can feel the center, yet still able to turn the shaft without the steering wheel. It can be on the tight side while just turning the bare shaft. Once you ad the wheel,...
  7. Replies
    5
    Views
    242

    TR2/3/3A Re: Side screen location.

    As Steve wrote, you may be a bit low. The "missing" material is simply a thick fold of material that extends out from the inside edge of the frame about 3/8 to 1/2", depending on how TRF finishes...
  8. Replies
    10
    Views
    272

    TR2/3/3A Re: Starter catches 50% of the time

    I think the Bendix drive gets ample lubrication from the spinning flywheel and extraneous lube from the engine, pilot bearing and throw out bearings. More than likely problem is old oil and dirt...
  9. Thread: Tr3a radio

    by CJD
    Replies
    15
    Views
    2,909

    TR2/3/3A Re: Tr3a radio

    The original mount looks like a real knuckle buster on the 1-2 shift?!?
  10. Thread: Gaskets

    by CJD
    Replies
    9
    Views
    317

    TR2/3/3A Re: Gaskets

    Any of the options you mention will work...it's really up to you, so long as you understand the nature of the different sealers.

    On a good, straight, well prepared surface no sealer is needed for...
  11. TR2/3/3A Re: Question on torquing nut on steering box rocker shaft

    I hold the arm in a table vice while tightening. Of course the box has to be out of the car for that.
  12. TR2/3/3A Re: Advise on previously botched front end lower fulcrum support bracket.

    Best to compare to your good right side to figure out what's screwed up.
  13. Thread: TR3 Timing Chain

    by CJD
    Replies
    13
    Views
    1,416

    TR2/3/3A Re: TR3 Timing Chain

    If the tensioner goes the chain rattles against the sheet metal cover...makes a banshee of a racket like everything’s about to come apart!
  14. Replies
    6
    Views
    362

    TR2/3/3A Re: Restoration of 54 TR-2

    Just had a memory pop up. I really don’t know if wear occurs most at start up, but I do know the really pricy engines, like Rolls Merlins, Wrights, and many industrial diesels came from the factory...
  15. Replies
    25
    Views
    655

    TR2/3/3A Re: Starting from scratch what color

    Engine pic is ok...car pic great!
  16. Replies
    25
    Views
    655

    TR2/3/3A Re: Starting from scratch what color

    Front plate was black, timing cover black with a grey noise deadener, sump black, oil filter a sort of aqua blue/green, oil filter head natural, water pump black, pulley and extension black, valve...
  17. Thread: TR3 Timing Chain

    by CJD
    Replies
    13
    Views
    1,416

    TR2/3/3A Re: TR3 Timing Chain

    An important step for installing the chain on a TR is to polish the chain links on the outer side, so there are no sharp edges to cut into the tensioner. The links are stamped at the factory, so...
  18. Replies
    6
    Views
    362

    TR2/3/3A Re: Restoration of 54 TR-2

    Fortunately the TR cams are very mild and the engine forgiving. In a high lift flat tappet engine, spinning a fresh motor with the plugs out will kill the cam, as the cam sees no lubrication until...
  19. Replies
    6
    Views
    362

    TR2/3/3A Re: Restoration of 54 TR-2

    If you properly lubed the engine during assembly it should be good for a couple years. Using the starter to turn the crank takes several minutes to get enough oil through the system, and you are...
  20. Thread: Over drive

    by CJD
    Replies
    53
    Views
    2,394

    TR2/3/3A Re: Over drive

    That amount of amperage indicates the plunger is not making it full travel.
  21. Thread: TR3A Gas Cap

    by CJD
    Replies
    15
    Views
    602

    TR2/3/3A Re: TR3A Gas Cap

    If the carb has been rebuilt in the last 5 years, then you could just replace the jet seals, but if it has been longer or you aren’t sure, then probably best to buy the whole rebuild kit. It’ll save...
  22. Thread: TR3A Gas Cap

    by CJD
    Replies
    15
    Views
    602

    TR2/3/3A Re: TR3A Gas Cap

    I found an Oring at Ace that has been working for several years. The fiber never worked well.

    Most fumes come from the carb jets leaking.
  23. Thread: TR3 Timing Chain

    by CJD
    Replies
    13
    Views
    1,416

    TR2/3/3A Re: TR3 Timing Chain

    The deflection would be left and right at the mid point between the sprockets...not for and aft.

    I don't have an opinion on keeping old parts. I replaced my sprockets, chain and tensioner 3 years...
  24. Replies
    27
    Views
    824

    TR2/3/3A Re: Speed O not working

    With the o-ring it can fit quite a bit looser without leaking. I think I put mine in a drill press and sanded the OD before it went back in. The break is interesting too. The cable must have...
  25. Replies
    17
    Views
    547

    TR2/3/3A Re: OD cover plate gasket sealer.

    Hmmm...a thought since I have a mill now?!? It is kinda complicated though, as it includes the solenoid mount and through shaft.

    When I first rebuilt the OD I installed the shaft seal on the...
Results 1 to 25 of 5388
Page 1 of 216 1 2 3 4