Search:

Type: Posts; User: Graham H; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    218

    TR2/3/3A Re: tr3 spare tire fit

    Does it fit if you take the seal out? i'm a bit concerned about the width of the aperture , your photo looks like it is a close fit at the ends. If you bend the cover flatter it will grow longer and...
  2. Replies
    17
    Views
    547

    TR2/3/3A Re: OD cover plate gasket sealer.

    Hello David,

    I don't think the spring tension is strong enough to bend the plate but as I mentioned before the steel tube that holds the accumulator cylinder in the housing can be loose and drop...
  3. Replies
    12
    Views
    428

    TR6 Re: Why were all these shims in there?

    Nice TR3 and the driver looks like a keeper as well?

    Graham
  4. Replies
    8
    Views
    268

    TR2/3/3A Re: OD angle drive engaging the speedo cable

    Correct Jim, then follow the foot brake fluid pipe forward through the same large grommet up the fire wall and back into the back of the speedo through the grommet to the left of the battery box.
    ...
  5. Replies
    8
    Views
    268

    TR2/3/3A Re: OD angle drive engaging the speedo cable

    I think you will find it all lines up nicely without the angle drive.

    Graham
  6. Replies
    8
    Views
    268

    TR2/3/3A Re: OD angle drive engaging the speedo cable

    Why are you using an angle drive, I thought the TR3 didn't have one?

    Graham
  7. Replies
    19
    Views
    644

    General TR Re: The RT story video.

    That is probably as good as anything David, as you are never likely to take it off maybe drill a small hole and tape a screw into the stanchion just to stop it rotating down. I think you are onto a...
  8. Replies
    19
    Views
    644

    General TR Re: The RT story video.

    I think I have put my mirror up before, it mounts in one of the stanchion screw holes and is out of the way of the side screen. They were made by a TR Register Australia member bu I see his add in...
  9. Thread: Over drive

    by Graham H
    Replies
    53
    Views
    2,394

    TR2/3/3A Re: Over drive

    That black piece is the rubber dust cover, I left it off tends to restrict the plunger

    Graham
  10. Thread: Over drive

    by Graham H
    Replies
    53
    Views
    2,394

    TR2/3/3A Re: Over drive

    That's what I did David, ordered a new one because it would not pull up on the first high amp circuit . When I took it apart I found a loose connection , resoldered it and it works fine. The relay...
  11. Thread: Over drive

    by Graham H
    Replies
    53
    Views
    2,394

    TR2/3/3A Re: Over drive

    These photos show how I mounted the relay and where the wires go, when they come out of the tunnel cover they just sit on the floor under the carpet and run up the firewall

    Graham620446204562046
  12. Replies
    27
    Views
    824

    TR2/3/3A Re: Speed O not working

    David,

    The cable route for right hand drive takes it through the chassis grommet for the brake line then up to the firewall grommet to the right of the battery and for left hand drive the grommet...
  13. Replies
    17
    Views
    547

    TR2/3/3A Re: OD cover plate gasket sealer.

    That steel peg in the cover plate should come out if you want to resurface it, or you could try two gaskets.

    Graham
  14. Replies
    17
    Views
    547

    TR2/3/3A Re: OD cover plate gasket sealer.

    David, I found the steel tube that holds the accumulator piston in the cylinder tends to droop if you fit the end plate with the box sitting in its normal upright position. I tend to lay the box on...
  15. Replies
    17
    Views
    673

    TR2/3/3A Re: Clutch through out fork misaligned

    My 6 box doesn't have grease nipples for the clutch shaft, Triumph must have relied on oil leaks for lubrication?

    Graham
  16. Replies
    17
    Views
    673

    TR2/3/3A Re: Clutch through out fork misaligned

    David,

    I have seen this problem on another Forum and from memory the problem was with the new shaft, either the taper pin or the locater slot is in the wrong place. Leaving the locater pin out...
  17. Replies
    12
    Views
    532

    TR2/3/3A Re: such strange thread on gear shift knob

    Yes Keith, I got one from Macy's had to do some fast talking to get them to send it to Australia without charging silly money for shipping. At the time it was the only one i could find World wide.
    ...
  18. Replies
    12
    Views
    1,083

    TR2/3/3A Re: OMG problem葉he doors are too tight

    All food for thought, one thing we tend to forget is how much of our gaps are taken up in the final paint coat, both sides of the hinges pillars door frame and surround and so it goes on.

    Graham
  19. Replies
    12
    Views
    1,083

    TR2/3/3A Re: OMG problem葉he doors are too tight

    You may have more luck trying to move the fenders forward, there is usually a bit of wiggle room in the mounting holes otherwise its make the doors shorter I don't think you will get much out of the...
  20. Replies
    14
    Views
    2,171

    Re: Merry Christmas to all

    Merry Christmas Basil

    Graham
  21. Thread: Rust for sale

    by Graham H
    Replies
    2
    Views
    484

    TR4/4A Re: Rust for sale

    The post has been deleted.

    Graham
  22. Replies
    14
    Views
    777

    TR2/3/3A Re: Bracing the tub for removal fom frame?

    this is how I braced my 3A see that masking tape on that sharp corner? I still have dents in my head , even managed to bash it with the tape on.

    Graham61587
  23. Replies
    21
    Views
    1,366

    TR2/3/3A Re: Frame off vs. body on restoration

    Im not to keen on replacing all the rubber mounts as the modern stuff is no match for the original, try to reuse every thing you can.

    Graham
  24. TR2/3/3A Re: Fitting the original tr3 transmission cover over a tr6 overdrive

    The rubber piece in your photo is missing the the part that the cable goes into, if you take away the angle drive it should all line up with the slot in the tunnel cover. I have the TR6 box with A...
  25. Replies
    2
    Views
    449

    TR2/3/3A Re: Firewall passenger side

    Spot on Keith.

    Graham
Results 1 to 25 of 249
Page 1 of 10 1 2 3 4