Search:

Type: Posts; User: mastaphixa; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    185

    TR4/4A Re: A type Overdrive Oil Leak Fix

    Randall,
    Thanks for the advise and the link to the manual!!! I have read the Buckeye article and will have a look a the ball lift going back together. This one is freshly overhauled and I did use...
  2. Replies
    3
    Views
    185

    TR4/4A A type Overdrive Oil Leak Fix

    I have been bench testing my A type over drive and have discovered a leak between the housing the solenoid mounts to and the case of the overdrive. Removing it looks fairly straight forward but I...
  3. Replies
    2
    Views
    195

    TR2/3/3A Re: Transmission Removal Tool Thread

    Yes! Thanks.
  4. Replies
    2
    Views
    195

    TR2/3/3A Transmission Removal Tool Thread

    I have searched till my fingers hurt but I cannot find the thread that shows a picture of a clever device used to support the transmission during removal/installation. It bolts to the fire wall, has...
  5. Thread: Over drive

    by mastaphixa
    Replies
    25
    Views
    1,167

    TR2/3/3A Re: Over drive

    Thank you randall!
  6. Thread: Over drive

    by mastaphixa
    Replies
    25
    Views
    1,167

    TR2/3/3A Re: Over drive

    Having accomplished the OD wiring installation with the addition of the diode and the fuse holder, I am wondering what an appropriate fuse rating would be? I think in this case I'm trying to protect...
  7. TR2/3/3A Re: How to restore a bluemels steering wheel

    Thank you for posting this! I have it book marked for the future.
  8. Replies
    3
    Views
    271

    TR2/3/3A Identification of Rack and Pinion Unit

    I am working on my friends 60 Tr3 and am trying to identify the installed rack and pinion unit. From the paperwork that came with the car I can tell the mod was done some time in 1994. Robert...
  9. Replies
    7
    Views
    288

    TR2/3/3A Re: Gearbox Oil Improvement

    Yes it was. Very timely. Thanks!
  10. Replies
    7
    Views
    288

    TR2/3/3A Re: Gearbox Oil Improvement

    Is the OD serviced separately from the transmission?
  11. Replies
    4
    Views
    191

    TR2/3/3A Re: Rocker Shaft Pedestal Lock Washers

    Flat washers and Locktite it is.
  12. Replies
    4
    Views
    191

    TR2/3/3A Rocker Shaft Pedestal Lock Washers

    While re-installing the rocker shaft to the head, I notice the new lock washers I am using under the pedestal nuts gouge the aluminum pedestal material leaving little flecks of aluminum behind. I am...
  13. Replies
    3
    Views
    268

    TR2/3/3A Re: What Flywheel is this?

    I weighed this one and it came to 20# 8 oz so it's been lighted a bit. It doesn't look like the counter bores for the bolts were part of that, but on both of the other flywheels I have the holes for...
  14. Replies
    3
    Views
    268

    TR2/3/3A What Flywheel is this?

    So I'm looking at my flywheel hardware making sure it doesn't interfere with the modified rear crank seal I've just installed and realized this flywheel has the bolts setting in a counter bore unlike...
  15. Replies
    1
    Views
    157

    TR2/3/3A Another TR3 Piston Ring Gap Question

    I'm using 86mm pistons/sleeves on my rebuild and am measuring ring gaps. I am using the TR4 spec .010 - .015" for the compression rings. What is the appropriate gap for the oil scraper rings? Mine...
  16. Replies
    1
    Views
    291

    Wanted TR3/4 Cam Bearings

    I am quite sure I'm not the only person to have damaged a cam bearing trying to install them. I am in need of 1 of the wide cam bearings. If anyone has 2/3s of a set laying around I'd be glad to...
  17. Replies
    1
    Views
    207

    TR2/3/3A Red or Blue Loctite

    So I'm ready to install the sludge plugs back in my crankshaft. Knowing how hard it is to get something apart that has had red loctite applied I am hesitant to use it for this application, but I...
  18. Replies
    6
    Views
    376

    TR2/3/3A Re: Please Help ID This Piston

    Andrew Mace: The only writing on the tops of the pistons are a cylinder number. Sarastro: My caliper is calibrated.
  19. Replies
    6
    Views
    376

    TR2/3/3A Please Help ID This Piston

    Initially I thought this was a TR2 piston, but when I mic'd it I couldn't make sense out of it.
  20. Replies
    7
    Views
    423

    TR2/3/3A Re: Crankshaft Oil Galley Plugs

    No matter what I do, when uploading images, they are not placed in the order that I want, so the basic process goes like this. I used a counter sink to provide a basic center for the #16 (.177")...
  21. Replies
    7
    Views
    423

    TR2/3/3A Re: Crankshaft Oil Galley Plugs

    I have successfully removed the soft aluminum galley plugs from my crankshaft. A friend of mine machined three drill bushings that really helped with the process. I ran across a video showing a...
  22. Replies
    17
    Views
    711

    TR2/3/3A Re: Standard Engine Trust Washer Thickness

    Randall and John, thanks. I was focused on the .004 - .006 in the remarks column. the .0117" makes sense now. I do have a new set of standard washers that just showed up from BPNW so I will play...
  23. Replies
    17
    Views
    711

    TR2/3/3A Re: Standard Engine Trust Washer Thickness

    Randall,
    Thanks. Where is the .0117" coming from? If it is experience, I certainly respect that, but am I overlooking something in the manual?
  24. Replies
    17
    Views
    711

    TR2/3/3A Re: Standard Engine Trust Washer Thickness

    No racing here. So at what point would you be concerned with crank end float? I want to make a note in my manual.
  25. Replies
    3
    Views
    297

    TR2/3/3A Re: Crankshaft Pulley Configurations

    John, the speedi sleeve repair is kind of how I got into all of this. I was inspecting the hub and noticed a deep groove in it and started looking at speedi sleeve repairs and when I measured the...
Results 1 to 25 of 122
Page 1 of 5 1 2 3 4