Search:

Type: Posts; User: rjc157; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    1,017

    TR6 Re: Rocker panel hole

    You do not want to take the rocker panel off it's way too big a job grind down around the hole and see the extent of the damage if you don't want to bring it to a shop to weld a piece of metal in...
  2. Thread: New Addition

    by rjc157
    Replies
    6
    Views
    624

    TR5/TR250 Re: New Addition

    You have to turn them before it's too late.
  3. Thread: New Addition

    by rjc157
    Replies
    6
    Views
    624

    TR5/TR250 Re: New Addition

    Joe seen your car at the Hermitage a few times was the purchase local . TG the girls are Yankee fans.
  4. Replies
    6
    Views
    505

    TR6 Re: Triumph TR6 Windshield seal on ragtop

    Check out Elin Yakov aka Rusty Beauties he goes through the whole top instillation on youtube
  5. Replies
    6
    Views
    617

    TR4/4A Re: Pricing a TR4 project car

    For a non overdrive car I think 10 is the max if it were a 250 maybe his asking price .
  6. Replies
    16
    Views
    841

    TR6 Re: 72 TR6 clutch high engagement point

    Moss sells an adjustable rod for about 35.00 it should help.Maybe with all new parts he has nothing to compare it too unless you have a tr6.
  7. Replies
    16
    Views
    841

    TR6 Re: 72 TR6 clutch high engagement point

    Is the push rod in the slave in the middle position.
  8. Replies
    9
    Views
    778

    TR6 Re: new TR6 owner looking for advice

    Not a fan of Pertronix go back to points and see what happens . Could be the carbs maybe a time for a rebuild.Check the wire from the dist to the coil make sure it's not cracked and the ground wire...
  9. Replies
    22
    Views
    1,266

    TR6 Re: grinding right rear wheel

    At this point take out the driveshaft and change the u-joint you will regret not doing it have it balanced bring it to a machine shop don't waste your time it will be money well spent .
  10. Replies
    22
    Views
    1,266

    TR6 Re: grinding right rear wheel

    To be honest I would bring it to a pro the bearing needs to be pressed out
  11. Replies
    18
    Views
    1,166

    TR6 Re: Rusted Trunnion Pivot Bolt

    More than likely the sleeve is rusted in there your never going to get it out with any kind of pb blaster your only chance is with a torch and that might not work you might just consider getting a...
  12. Replies
    22
    Views
    1,266

    TR6 Re: grinding right rear wheel

    Terry I did mine that way and was successful bought a 6 in bench vice from HF and it fit ok just take it slow it will work .
  13. Replies
    22
    Views
    1,266

    TR6 Re: grinding right rear wheel

    If your talking about the u-joints in the axles it's easier said than done there are some vids on YouTube that make it look easy if you don't have a big ass vice it's a PITA if it's the driveshaft...
  14. Thread: fuel injection

    by rjc157
    Replies
    4
    Views
    799

    General TR Re: fuel injection

    Patton does have some CFI have zero both are very expensive options
  15. Replies
    8
    Views
    1,778

    TR6 Re: Frame Pics, some bad news

    can't see any of the pics
  16. Thread: Electric fan

    by rjc157
    Replies
    5
    Views
    846

    TR6 Electric fan

    In the process of installind Rick Pattons fan eliminator and purchased a 16 in fan off of ebay since electrics isn't my strong point can someone out there advise me where as to attach the 12v red...
  17. Replies
    21
    Views
    2,484

    TR6 Re: Need help with a 1969 triumph tr6

    Chances are it's a loose wire somewhere check what you did and make sure it's connected properly and grounded get a test light and start from the battery and work your way down to the starter then...
  18. Replies
    8
    Views
    2,114

    TR6 Re: Toyota Transmission conversion

    I hope you know to change that piece you have to split the trans Herman is a very nice man to deal with but get him on the phone to talk to him you might not have to change that piece his shifter...
  19. Replies
    14
    Views
    2,332

    General Tech Re: Had it with Venders

    Give John a call at Sports & Classics he has a lot of nos parts if he has one be ready to pay
  20. Replies
    7
    Views
    1,128

    TR6 Re: Brake caliper question

    Just did mine you have to push the piston down first when you put the wire clip in you have to start at the bottom where that lip is in order to hold it in place
  21. Replies
    3
    Views
    658

    TR6 Re: 69 project in Hotlanta

    If the frame is ok that's a real bargain
  22. Replies
    7
    Views
    905

    TR6 Re: 5-speed conversion

    ok
  23. Replies
    7
    Views
    905

    TR6 Re: 5-speed conversion

    Are those something that you manufacture
  24. Replies
    7
    Views
    905

    TR6 5-speed conversion

    Can't seem to find anything on the web have any of the 5-speed conversion guys made a HVDA 5-speed emblem other than the sticker that Herman supplies
  25. Replies
    2
    Views
    1,086

    TR6 Re: TR6 Painting/Restoration

    I think you should try to post some pics of your car to what extent of restoration are you looking for a so called restoration shop will charge a ton of money if you can do some of the work yourself...
Results 1 to 25 of 481
Page 1 of 20 1 2 3 4