Search:

Type: Posts; User: STeve 1958; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    11
    Views
    478

    TR2/3/3A Re: Tierod Dyslexia?

    Does righty tighty, lefty Lucy help. But your saying it's the opposite thread so Righty Lucy, lefty tighty.
    Ok that doesn't help at all !

    It looks a little like that nut is cross threaded in the...
  2. Replies
    11
    Views
    478

    TR2/3/3A Re: Tierod Dyslexia?

    [QUOTE=TR3driver;1132556]Yes, left hand in the photo. With it laying as in the photo, and the wrench sticking up, you would pull the wrench towards you. Or another way to look at it, turn the nut...
  3. TR6 Re: 74 TR6 Interior - Padded dash and heat/sound material

    I used Kill-Mat which worked well. Same as Dynamat. I chose to use the thinner mat to save weight and then put two layers on the left side of the transmission hump. On top, not under.
    Make sure...
  4. Replies
    9
    Views
    421

    TR2/3/3A Re: Front apron position

    You really don't want to get involved in bending the front apron, so bending the fenders is the best alternative. The apron is what it is. There is no right or wrong if it looks good.
  5. TR2/3/3A Re: glass and ring into new bee hive sockets

    You're right Keith. I think I said it backwards. My memory is fading but but I clearly remember the hours of swearing and then feeling really stupid.
  6. TR2/3/3A Re: glass and ring into new bee hive sockets

    I spent hours trying to get mine on and then realized I was doing it wrong. Five minutes later I'm done.
    The bee hive goes over the top of the seal and only the Crome ring goes under the outer lip....
  7. Thread: The Book!!!

    by STeve 1958
    Replies
    25
    Views
    1,086

    TR2/3/3A Re: The Book!!!

    If the fluid pressure in the clutch is not releasing, the slave cylinder will remain depressed and tight. If the slave cylinder releases but the clutch doesn't you've got a bigger problem inside the...
  8. Replies
    3
    Views
    384

    TR2/3/3A Re: An Electric TR3 ??

    I think it's a great idea, if you have a TR3 with a bad engine. But if you put 100hp electric in it you might have to beef up the transmission / rear end. Or you could put a torque limiter on it. I...
  9. Replies
    16
    Views
    904

    TR2/3/3A Re: tr3 spare tire fit

    I think you can bend it without cracking the paint or at least just cracking the paint on the inside. Little choice but to put on your big boy pants and go for it. I like your original idea of a...
  10. Thread: Quiet

    by STeve 1958
    Replies
    12
    Views
    687

    TR2/3/3A Re: Quiet

    I used Kilmat 50 mil. It was easy and works. They also have 80 mil. I hear Dynamite is hard to work with but this may be because it is thicker and less stretchy. I would put the best stuff over the...
  11. Replies
    15
    Views
    889

    TR2/3/3A Re: TR3A Gas Cap

    I don't like these heat shields because they go under the carburetors so they can't be removed without removing the carb.
    I made one just like this one (see TR3driver) but with only two bolt holes. ...
  12. Replies
    3
    Views
    397

    TR2/3/3A Re: Timing chain tensioner.

    I little black grease will fix that up good as new. ;-)
  13. TR2/3/3A Re: All new valve train - no adjustment at rocker arms

    Would it be possible (advisable) to grind the push rods down a 16th. This is more of a question than an answer. In 1974 I had to buy a thicker head gasket to reduce the compression. Might still be...
  14. Replies
    17
    Views
    1,037

    TR2/3/3A Re: Carpet and upholstery installation

    Martx-5. That is awesome. ****, now I have to do mine over again.
  15. Replies
    17
    Views
    1,037

    TR2/3/3A Re: Carpet and upholstery installation

    61859I just did mine. Carpets are easy, just lots of contact cement. I also put "Killmat" under the carpet for sound and heat. Definitely recommend over the hump to keep your right leg cool. Vinyl...
  16. TR2/3/3A Re: When to use R (Rich) needles in my SU's?

    A rich mixture produces more horse power, however it does not take a special needle to get a rich mixture. just turn the nut.
    Thickening you damper oil will also richen your mixture when you first...
  17. TR2/3/3A Re: The chrome beading is rubbing on the hood

    I used a long 3" wide nylon strap like you would see on lawn furniture. Tied a loop at each end and used a wood block clamp to pull the loops together. Those clamps aren't that strong but they have...
  18. TR2/3/3A Re: The chrome beading is rubbing on the hood

    I put a strap around the hood and squeezed it with a wood block clamp. This method didn't damage the paint and pulled the back corners in nicely.
  19. Replies
    4
    Views
    602

    TR6 Re: I will not be buffing out -opinions?

    I lost a corvette and a Jag, all at once, to a Eucalyptus tree. Long story on the insurance, which I will no bore you with.
    If the car runs good, etc., buy a door and a fender. Good luck. Pictures...
  20. TR2/3/3A Re: location of the coolant drains on a tr3a

    I remember, as a kid, opening up the drains and then putting a garden hose in the filler cap. Made a good seal and blew all kinds of junk out of the system. Don't know if that's the right way to do...
  21. Thread: The bat

    by STeve 1958
    Replies
    4
    Views
    626

    TR2/3/3A Re: The bat

    6110961110try again
  22. Thread: The bat

    by STeve 1958
    Replies
    4
    Views
    626

    TR2/3/3A The bat

    6108861089They called it "Trunk or Treat". Of course I called it "Boot or Sweetie"
    This was my daughters idea which won for most photogenic. Gave out a thousand pieces of candy.
    Do I go to Triumph...
  23. Replies
    21
    Views
    3,161

    TR2/3/3A Re: TR3 choke cable connection help needed

    The linkage can be located on the manifold side, centered, or on the fender side. The important thing is to bend the bracket that holds the cable shroud so that you get good alignment with choke on...
  24. Replies
    14
    Views
    1,010

    TR2/3/3A Re: Windshield difficulties

    There is such a thing as an "Easy-Out" which is not that easy but usually gets it out.
  25. Replies
    11
    Views
    891

    TR2/3/3A Re: back seat bracket

    What did you end up using for the wheel arches. Foam rubber, cotton, nothing. They look better than mine with cotton backing.
Results 1 to 25 of 190
Page 1 of 8 1 2 3 4