Search:

Type: Posts; User: EWD; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    161

    TR6 » Re: 74 TR6 - Carbon canister rebuild

    Thx for the quick reply and link. Yep, basically the same except for the 2 screens on the TR6. The grid on one is more than twice as open as the other. I’m guessing the smaller grid goes on top ( 50%...
  2. Replies
    2
    Views
    161

    TR6 » 74 TR6 - Carbon canister rebuild

    Putting my canister back together and, regrettably, did not take a photo. I have 2 screens, one is mesh and the other is more open. Which one goes on top (toward top of car inside of canister). I...
  3. Thread: Trunion Install

    by EWD
    Replies
    0
    Views
    152

    TR6 » Trunion Install

    In the middle of reassembling my front suspension. 2 questions:
    1. Trunion - Installing new parts. Having a problem getting the metal sleeve into the bushings. It goes easily into one side (using a...
  4. Replies
    0
    Views
    138

    TR6 » 74 TR6 - suspension bushing tightening

    Hi folks! Question please and I apologize if it’s been previously covered.
    I’ve removed and reconditioned and painted front end parts and am starting to put it back together using rubber bushings....
  5. Thread: Steering

    by EWD
    Replies
    3
    Views
    302

    TR6 » Re: Steering

    Thanks folks.
    Will
  6. Thread: Steering

    by EWD
    Replies
    3
    Views
    302

    TR6 » Steering

    Hi Folks -
    Replacing the original boots on my 74TR6 and found a wrap of some type of tape (perhaps masking) in front of the upper ball joint where the end of the boot sits. Was this a “grease stop”?...
  7. Thread: ‘74 Gauge bezels

    by EWD
    Replies
    0
    Views
    479

    TR6 » ‘74 Gauge bezels

    Hi folks.
    just finished refurbishing my gauges and one of the smaller ones (fuel) has a broken tab. Looking for a matching chrome bezel with a black inset to match the others. Have found the entire...
  8. TR6 » Re: ‘74 TR6 Interior - Padded dash and heat/sound material

    Thanks!
  9. TR6 » ‘74 TR6 Interior - Padded dash and heat/sound material

    Morning Folks -
    Two questions please:
    1. Latest thoughts on adhesive for padded dash. Getting ready to install a new dash. Use adhesive? If so, type and any tips? Certainly want to do it right the...
  10. Thread: ‘74 Tach

    by EWD
    Replies
    7
    Views
    1,233

    TR6 » Re: ‘74 Tach

    Thanks everyone. In the middle of cleaning the smaller gauges. The larger ones also need repair, blasting, and painting; so considering having them done. We'll see.
    Noticed that the smaller gauges...
  11. Thread: ‘74 Tach

    by EWD
    Replies
    7
    Views
    1,233

    TR6 » Re: ‘74 Tach

    Thx Ed. Yep. Finding out the same. FYI, Nisonger Instruments only rebuilds (they will sell you the gaskets) Cost for speedo and tach is $185 (each). They have the needles made to specs ($50) and...
  12. Thread: ‘74 Tach

    by EWD
    Replies
    7
    Views
    1,233

    TR6 » ‘74 Tach

    During cleaning the needle on my tach broke. What a bummer. Any thoughts on where to find a replacement short of buying a used tach for parts? (and then hoping to get the needle assembly off without...
  13. Replies
    7
    Views
    489

    Re: Greetings from Virginia!

    Yep! From Webb on 10/11/74.
    We lived in Vista Forest (off 221 past Poages Mill. Sub-division above Forest Edge).
  14. Replies
    7
    Views
    489

    Re: Greetings from Virginia!

    Hi AngliaGT. Interestingly, we lived in Roanoke for 10 years and that is where my TR6 was purchased new by the previous owner.
  15. Replies
    7
    Views
    489

    Greetings from Virginia!

    Started the restoration of my 74-TR6 a month ago. Tried to buy this car 20 years ago and the original owner finally relented. Fun project. Thankfully, Moss Motors is only 20 minutes away. I look...
Results 1 to 15 of 15