Search:

Type: Posts; User: Guy Marshall; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    61
    Views
    3,299

    Re: Randy Forbes

    All the best, Randy!
  2. Replies
    7
    Views
    426

    Re: BN6 Battery location

    Perfect. Thanks, steveg!
  3. Replies
    11
    Views
    675

    Re: Removing the Healey "Flash"?

    i was able to reach the retaining nuts from outside the car reaching up between the wing inner and outer. It was a bit of a stretch though... GL!
  4. Replies
    7
    Views
    426

    BN6 Battery location

    Hi all,

    A PO has replaced the two 6 vol batteries in my BN6 with a modern 12v battery which has been relocated in the boot. Unfortunately he forgot a battery tray so it rattles around the boot and...
  5. Replies
    6
    Views
    353

    Re: 100/6 Radiator cross member

    Thanks all,

    Yes, I suspect all the damage stems from a previous accident - before my time. I suspect driving an Austin Healey may not be the best place to have an accident involving the steering...
  6. Replies
    6
    Views
    353

    100/6 Radiator cross member

    Hi all,

    I replaced my water pump and noticed a very shabby repair on the front yoke that supports the bottom of the rad.

    The left side of the yoke has been reattached a good inch behind where...
  7. Replies
    3
    Views
    351

    Re: Rollover Bar BN6

    Thanks Randy. Rolling my own is very tempting... do you use mild steel? If so what gauge?

    Anyhow its for added safety/appearance for a street/fast-road car. A full cage is overkill (sorry!).
  8. Replies
    3
    Views
    351

    Rollover Bar BN6

    Hi guys

    I am considering a Rollover Bar for my BN6, but the only ones I can find are braced for a RHD car (the cross brace goes from bottom left to top right looking from the rear or the car) and...
  9. Replies
    44
    Views
    2,118

    Re: Running hot/Overheating

    Apologies if this has been linked already in this thread but https://www.healey6.com/Technical/I%20always%20wanted%20a%20COOL%20Car.pdf seemed like good advice to me.

    My 100/6 runs fine in France...
  10. Replies
    12
    Views
    676

    Re: Bellhousing Blues

    @steveg - mine had a pair of bastard 25mm M10 metric thread bolts forced in which is why they stripped. Happily the M10s were very short so I could clean up and extend the thread and replace with 1...
  11. Replies
    12
    Views
    676

    Re: Bellhousing Blues

    Score 1 for the good guys!

    A thread clean, then two longer 13/8" screws to replace the metric ones that had been forced in and a little loctite and the slave cylinder is working.
    56884

    I'll...
  12. Replies
    12
    Views
    676

    Bellhousing Blues

    Hi all,

    Reinstalling a rebuilt BN6 side change gearbox I discovered the PO had replaced the slave cylindar mounting bolts with 20mm M10 metric bolts which have now stripped out.

    There seems to...
  13. Re: Position of dowell bolts on Healey bell housing

    Hi guys - an old thread but a goodie.

    One more question - which way should the bellhousing bolts point? The bottom couple have to be "nuts forward" but is that true of the others? Normally I'd...
  14. Re: Driving Lights (picture posting opportunity!)

    Here's my 100/6 with the Rawles mounts. They are quite... chunky, but I like them! The lights are cheap spots from Deamon Tweeks.
    55101
  15. Thread: Hi

    by Guy Marshall
    Replies
    1
    Views
    196

    Hi

    Hi all - I'm Guy with an Austin Healey BN6 in Milton Keynes and Tarn et Garonne in France.

    If anyone knows about B&S 13HP mower engines that would be ace too!
Results 1 to 15 of 15