• SU H6 Carburetor Will Not Decelerate

    I have a 1962 Triumph TR3B with SU H6 carbs. After a recent disassembly, cleaning and reassembly of the carbs the RPM would not return to idle after a load. It continued at an accelerated rate whether under load or at a stop - racing. Only by "goosing" the throttle with the accelerator did the RPM drop, but still not to the proper idle - 600 - 900 RPM (or anywhere close to it).

    I checked that each throttle plate was centered in the barrel, that they closed easily and no "daylight" around the edges of the plate. The carb pistons went up and down easily, dash pots properly filled with the right oil, jet needles centered in the jets and not binding. No vacuum leaks at gaskets.

    After much investigation I discovered that I had two problems: (1) the throttle return springs were not set in high enough torsion and (2) the coupling assemblies on the connecting rod were slipping under load. I could not detect slippage at curb idle by manually manipulating the throttle linkage but under load it seems the connection to #2 carb slipped. This allowed at least #2 carb to remain with an open throttle plate vs. #1 carb. The coupling was just tight enough to respond to "goosing" the accelerator but having slipped it was now out of balance. Also, the shafts are made of brass and over time will score from the connectors, also contributing to possible slippage.

    By torsioning the springs another half turn and tightening the connecting couplings I now have proper carburation. (Note: I also have a slight vacuum leak on #1 at the throttle shaft due to wear. This affects balance and fuel consumption but was not the cause of the "racing" problem)

    I hope this helps someone. I couldn't find a similar discussion anywhere.

    I have attached the Moss plate showing the connectors (66) and the springs (77):

    https://mossmotors.com/triumph-tr2-3...retors-su-h6-1
    Comments 1 Comment
    1. karls59tr's Avatar
      karls59tr -
      Thanks for the info. I've been battling this problem for awhile. Usually had to goose the throttle to bring the idle down but never WOT like you experienced.
  • Recent Articles

  • Recent Forum Posts

    waltesefalcon

    Re: Yes Mickey, Irregardless is now a word.

    Regardless of whether or not it's in the dictionary you shouldn't use irregardless.

    waltesefalcon Today, 08:54 PM Go to last post
    billspohn

    Re: Alloy Wheel Upgrade

    Alloys all the way. The steel wheels aren't all that strong if you drive aggressively. I ran them on my MGA race car for a few races and tore the centres

    billspohn Today, 08:51 PM Go to last post
    billspohn

    Re: Volvo engine in a B

    No,it doesn't bolt in, but yes, it can be made to fit if you can weld etc.

    billspohn Today, 08:48 PM Go to last post
    Bob McElwee

    Re: Finally found it

    Greg, that was great, thanks.

    Bob McElwee Today, 08:32 PM Go to last post
    Mickey Richaud

    Re: Yes Mickey, Irregardless is now a word.

    I could care less.

    Mickey Richaud Today, 08:11 PM Go to last post
  • Recent Blog Posts

    Madflyer

    Madflyer

    As a new member and long time TR owner of a few TR's. I fine the same topics come up time and time again. Here are three I like best; What tire is best and where do I get them and what do they cost....

    Madflyer Yesterday 10:27 AM
    Factoryman2000

    Adding AC to BN7 Healey

    Hi,recently visited a well regarded restoration shop and saw the install of AC system on an MGB. The installer had ordered a dual Compressor pulley, and the original v belt now drove waterpump, Fan...

    Factoryman2000 07-05-2020 04:17 PM
    commonground

    New member from california. Bring back the herald

    I am pursuing the creation of a sixties Triumph Herald. Nearly unknown in the USA.. I had one here in the late 60s. Loved the car handling and packaging. Hated very poor British parts quality and...

    commonground 07-05-2020 02:11 PM
    Madflyer

    Madflyer

    Good morning all as a new member yesterday I found BCF quite good and as a long time TR owner, I still learn more each day and yesterday a great day for sure. I added my inputs to a number of post...

    Madflyer 07-05-2020 12:13 PM
    Ale

    Just bought 1975 Triumph TR6 that has sat for last 25 years

    Hello I am a new member, I was directed to the form by a friend. I have recently purchased a TR6 that hasnít moved or started it the last 25 years. Everything under the hood held up nicely and...

    Ale 07-03-2020 07:35 PM
  • Twitter