• SU H6 Carburetor Will Not Decelerate

    I have a 1962 Triumph TR3B with SU H6 carbs. After a recent disassembly, cleaning and reassembly of the carbs the RPM would not return to idle after a load. It continued at an accelerated rate whether under load or at a stop - racing. Only by "goosing" the throttle with the accelerator did the RPM drop, but still not to the proper idle - 600 - 900 RPM (or anywhere close to it).

    I checked that each throttle plate was centered in the barrel, that they closed easily and no "daylight" around the edges of the plate. The carb pistons went up and down easily, dash pots properly filled with the right oil, jet needles centered in the jets and not binding. No vacuum leaks at gaskets.

    After much investigation I discovered that I had two problems: (1) the throttle return springs were not set in high enough torsion and (2) the coupling assemblies on the connecting rod were slipping under load. I could not detect slippage at curb idle by manually manipulating the throttle linkage but under load it seems the connection to #2 carb slipped. This allowed at least #2 carb to remain with an open throttle plate vs. #1 carb. The coupling was just tight enough to respond to "goosing" the accelerator but having slipped it was now out of balance. Also, the shafts are made of brass and over time will score from the connectors, also contributing to possible slippage.

    By torsioning the springs another half turn and tightening the connecting couplings I now have proper carburation. (Note: I also have a slight vacuum leak on #1 at the throttle shaft due to wear. This affects balance and fuel consumption but was not the cause of the "racing" problem)

    I hope this helps someone. I couldn't find a similar discussion anywhere.

    I have attached the Moss plate showing the connectors (66) and the springs (77):

    https://mossmotors.com/triumph-tr2-3...retors-su-h6-1
    Comments 1 Comment
    1. karls59tr's Avatar
      karls59tr -
      Thanks for the info. I've been battling this problem for awhile. Usually had to goose the throttle to bring the idle down but never WOT like you experienced.
  • Recent Articles

    Htimsc

    First attempt at iMovie of my car

    I'm learning how to make iMovies - in this case of my BJ8. Taken last year in Carmel, California. The video is hosted on Vimeo, let me know if you have any problems viewing it. Comments on the video... read more
    Htimsc 02-15-2020, 09:57 PM
  • Recent Forum Posts

    Graham H

    Re: tr3 spare tire fit

    Does it fit if you take the seal out? i'm a bit concerned about the width of the aperture , your photo looks like it is a close fit at the ends. If you

    Graham H Today, 02:28 AM Go to last post
    Bob_Spidell

    Re: BN2 clutch pedal and exhaust downpipe

    Well, I kind of hedged a little; I heard they all had the problem but, somewhere out there somebody doesn't and I would have been technically incorrect.

    Bob_Spidell Today, 01:44 AM Go to last post
    Randy Forbes

    Re: Diff refurbish

    It has been a long time since I've had an MGB (something in the works right now....) but there were two (2) driveline "fixes" that I would do

    Randy Forbes Today, 12:38 AM Go to last post
    Branson

    Re: Whole project must go

    Man I could use a straight pair of front fenders and some misc. odds and ends for my '65. Do you still have the parts available or is it all gone?

    Branson Today, 12:29 AM Go to last post
    pdplot

    Re: DNA tests

    I think I'm related to an African prince. He just sent me an email offering money - a LOT of money.

    pdplot Today, 12:04 AM Go to last post
  • Recent Blog Posts

    ggraham8

    Armstrong "RX" Shocks

    Does anyone know what the "RX" is for that is embossed on my shocks? see picture

    ggraham8 02-11-2020 02:13 PM
    Lockheed-driver

    TR2 manifold question

    Hi All. Iíve been restoring a TR2 for some time now. Learning as I go. I have both manifolds restored and ready to install. I started to look at the box full of bits that the previous owner had used...

    Lockheed-driver 02-03-2020 10:18 AM
  • Twitter