• SU H6 Carburetor Will Not Decelerate

    I have a 1962 Triumph TR3B with SU H6 carbs. After a recent disassembly, cleaning and reassembly of the carbs the RPM would not return to idle after a load. It continued at an accelerated rate whether under load or at a stop - racing. Only by "goosing" the throttle with the accelerator did the RPM drop, but still not to the proper idle - 600 - 900 RPM (or anywhere close to it).

    I checked that each throttle plate was centered in the barrel, that they closed easily and no "daylight" around the edges of the plate. The carb pistons went up and down easily, dash pots properly filled with the right oil, jet needles centered in the jets and not binding. No vacuum leaks at gaskets.

    After much investigation I discovered that I had two problems: (1) the throttle return springs were not set in high enough torsion and (2) the coupling assemblies on the connecting rod were slipping under load. I could not detect slippage at curb idle by manually manipulating the throttle linkage but under load it seems the connection to #2 carb slipped. This allowed at least #2 carb to remain with an open throttle plate vs. #1 carb. The coupling was just tight enough to respond to "goosing" the accelerator but having slipped it was now out of balance. Also, the shafts are made of brass and over time will score from the connectors, also contributing to possible slippage.

    By torsioning the springs another half turn and tightening the connecting couplings I now have proper carburation. (Note: I also have a slight vacuum leak on #1 at the throttle shaft due to wear. This affects balance and fuel consumption but was not the cause of the "racing" problem)

    I hope this helps someone. I couldn't find a similar discussion anywhere.

    I have attached the Moss plate showing the connectors (66) and the springs (77):

    https://mossmotors.com/triumph-tr2-3...retors-su-h6-1
  • Recent Articles

  • Recent Forum Posts

    Riquet1963

    Re: Temperature sensor Help me

    Hello


    And for my second question?
    In fact I search if I need a seal between this bulb and the water or this bulb is encapsulated

    Riquet1963 Today, 12:18 PM Go to last post
    Basil

    Re: Aging Rockers

    I'm a fan of Tim Hawkins. Funny without needing to go low or dirty.

    Basil Today, 12:16 PM Go to last post
    Jerry

    Re: New Member - Austin Healey BN1 & Austin 7 Special

    Yes, pics of the Austin 7 ! I don't have one, but I do have a Morris 8. 1936. Not so different. We have a friend here that has an Austin 7 but has

    Jerry Today, 12:05 PM Go to last post
    70herald

    Re: Scroll Air Compressor

    Here you go a bunch of smaller scroll compressors
    they cost a bit more than the Eastwood but probably better.
    https://www.aircompressorsdirect.com...mpressors.html

    70herald Today, 11:56 AM Go to last post
    Ron Trottier

    Re: Ron - New Member

    Well, a bit of both! I've owned my first '66 TR4A IRS since 1976 and its been sitting in my garage since 1977 when I totally rebuilt the engine. The

    Ron Trottier Today, 11:50 AM Go to last post
  • Recent Blog Posts

    Two Fifty Tuna

    TR 250 Rear Sway Bar

    The Tr 250 has aluminum rear trailing arms. Has anyone successfully installed a rear sway bar? I am concerned the stress of the end reactions will damage the mounting points on arms.
    Anyone care to...

    Two Fifty Tuna 12-05-2019 01:45 AM
    ajsblack

    ajsblack

    [QUOTE=ajsblack;1125840]I am a new member and have not used forums before. I have two TR3 a' a right hand drive Stag a 1949 2000 roadster (that I am restoring) a 1947 1800 for parts. I have a lot...

    ajsblack 11-29-2019 05:14 PM
  • Twitter